Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
If any parts are missing, please call 1-800-335-4348, Ext 12 Before proceeding, find your Fitness Cycle’s serial number, located on the underside of main frame, and enter here: Refer to this number when calling for service. A41.2 IT ALL STARTS WITH A VISION E4100 Parts Diagram E4100 Parts VISION FITNESS E4100 Parts Description Part # Description Count Dimensions Front Wheel Parts #60 Front Foot Wheel Axle 1 #61 Front Transport Wheels 2 #182 Outside Wheel Washers 2 #183 Wheel Attachment Nuts 2 Arm Assembly Parts #116 Right Arm 1 #115 Left Arm 1 #74 Plastic Arm Cam Cover 2 #105 Inside Cam Pulley 2 #106 Outside Cam Pulley 2 #169 Pulley Washer 4 Flat #107 Cam Pulley Spring 2 #183 Cam Pulley Locknuts 2 Frame Parts #62 Rear Foot Assembly 1 #167 Rear Foot Attach Bolts 4 20mm L x 8mm D #65 Seat Post 1 #108 Seat 1 #82 Top Cap 1 #176 Top Cap Screws 3 Console Assembly Parts #70 Console Mast 1 #78 Console Mast Plug 1 #168 Console Mast Bolts 2 38mm L x 8mm D #95 Console 1 #96 RPM Sensor Wire 1 #179 Upper Magnet Shift Cable 1 #143 Lower Magnet Shift Cable 1 #163 Console Attachment Bolts 6 11mm L x 5mm D Other Parts #91 Pedals 2 E4100 Assembly NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded inbefore completely tightening any ONE bolt. Step 1 • Rear Foot 1: Secure the Rear Foot Assembly (62) to the Frame by using the four Rear Foot Attachment Bolts (167). Step 2 • Seat and Seat Post 1: Slide the Seat Post (65) into the frame seat post receiver tube. The seat post numbers should be facing the right or seat pin side of the Fitness Cycle. NOTE: Both nuts in the Seat Clamp should be tightened at the same time, to ensure a proper fit. 2: Attach the Seat (108) to the Seat Post (65) and tighten securely. To avoid scratching the seat postpaint, always hold the the seat pin knob out when adjusting the seat post height. Step 3 • Console Mast 1: Remove the Top Cap Screws (176) which hold the Top Cap (82) to the frame. Then remove the Top Cap (82). NOTE: DO NOT thread in the Water Bottle Cage Bolts yet. Never slide the Top Cap (82) on or off withthe Waterbottle Cage Bolts threaded in, as they will scratch the paint on the Console Mast (70). 2: Slide the Top Cap (82) over the bottom of the Console Mast (70). The VISION decal on the Console Mast (70) should be facing forward, away from the rider. 3: Locate the RPM Sensor Wire (96) and the Lower Magnet Shift Cable (143). Holding the Top Cap (82) and Console Mast (70) above the frame console mast receiver tube, guide the RPM Sensor Wire (96) and the Lower magnet Cable (143) through the Console Mast (70) while simultaneously slidingthe Console Mast (70) into the receiver tube. 4: Lift the Top Cap (82) up, install the two 38mm-long Console Mast Allen bolts (168) and tightensecurely. 5: Now slide the Top Cap (82) back into place. Make sure that the back end of the Top Cap (82) isnested fully into the Seat Cap groove. Secure the Top Cap (82) by threading the three Top Cap Screws back into their holes. NOTE: Check that there are no large gaps between the Top Cap (82) and the Side Covers. Step 4 • Console 1: Feed the Upper Magnet Shift Cable (179) into the topmost opening of the Console Mast (70). 2: Plug the RPM Sensor Wire (96) into the Console (95). DO NOT PINCH the RPM Sensor Wire (96) between the Console (95) and the Console Mast (70). Make sure the cable fits in the slot cut in theConsole Mast Mount. 3: Mount the Console (95) to the Console Mast (70) using the six Console Attachment Phillip Head Bolts (163). E4100 Assembly Step 5 • Connect Magnet Shift Cable 1: Turn the Tension Knob to position 8. Reach inside the openingof the Console Mast (70) and connect the Upper Magnet ShiftCable (179) to the rectangular red cable-slide on the end of theLower Magnet Shift Cable (143), as shown in the accompanyingillustrations. 2: While holding the metal separating tab (Figure 5), turn theTension Knob to Level 1 and then pull the tab out and discard. 3: Press the Console Mast Plug (78) into the opening ofthe Console Mast (70). Step 6 • Install Arms and Front Wheels 1: Tip the Fitness Cycle back until it is balanced on the Seat andthe back of the Rear Foot Support. Place cardboard beneaththe seat to avoid tearing or marring the seat cover. 2: Identify the Left and Right Arms (115 & 116). Insert the FrontFoot Wheel Axle (60) through the frame axle hole. 3: Remove the Cam Pulley Locknut (183), the two Pulley SpringWashers (107), and the Outside Cam Pulley (106) from the CamPulley Arm (75). Note the order and direction of these partsbefore removal. 4: Place the bottom hole of the Right Arm (116) onto the FrontFoot Wheel Axle (60). Position the Right Arm (116) so that thechromed slot rests against the inside Cam Pulley (105). 5: Place a thin layer of grease on the pulley surfaces. Reassemblethe parts removed in the above steps onto the Cam Pulley Arm(75). Do not yet tighten the Cam Pulley Locknut (183). E4100 Assembly 6: Slip the Front Transport Wheel (61...