Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
We recommend setting the speed scale and wheel circumference before installing the computer. Precautions Remember to watch the road or trail while riding. Watching your bicycle computer makes it difficult to see upcoming obstacles. Awareness of potential road, trail or traffic problems should be your main concern. Main Unit/Accessories 8 1 Contents: 1. Main Unit 5. Magnet 9. Mounting Clamp 2. Bracket 6. Wire Securing Tape 10. Rubber Pad for Clamp 3. Wire 7. Zip Tie 4. Wheel Sensor 8. Bracket Rubber Pad 2 3 4 5 67 9 10 Page 1 button to switch between miles and First Second kilometers. Press both L & R buttons to Point Point confirm and enter Wheel-Circumference Measure the distance which setting as shown in fig 4. Table 1. Setting values reference table is your circumference If incorrect data appears on the screen, Preparation - Must be completed before operation please re-install battery again. fig 4 Wheel/Tire Size Wheel size Setting Wheel/Tire Size Wheel size Setting 16” 1300 700 X 20C 2074 20” X 1.75” 1600 700 X 23C 2085 24” X 1.95” 1920 700 X 25C 2100 26” X 1” 1950 700 X 28C 2135 650 X 20C 1945 700 X 32C 2155 650 X 23C 1990 700 X 35C 2175 26” X 1.5” 2030 700 X 38C 2180 26” X 1.9” 2055 700 X 40C 2190 26” X 2.0” 2074 700 X 1- 1/ 4” 2160 26” X 2.2” 2100 1. Measure the wheel circumference before setup Refer to fig. 1 ( 25.4 mm equals 1 inch) or Table 1 to get the wheel circumference in millimeters. Confirm and note this number in the manual for later use here:__________ 4. Setting the wheel circumference (100mm- 2999mm) Sensor 2.0 has 2 wheel circumference settings. The display shows 1/ 2155 and the last two digits “55” will flash. Advance them rapidly by holding down the R button, or one at a time by pressing the R button ( or go backward by holding the L button). When desired number (confirmed and marked from fig. 1 or Table 1 and between 100mm- 2999mm) has been achieved, press both L & R buttons for confirmation and the next two digits will flash. Repeat the same method to set up the completed numbers. Press both L & R button to confirm then go to Odometer program function (screen will show “ODO 00000”. Please see the following method a. to complete Odometer setting). The display will show 2/2074, follow the method of bike 1 to complete setting circumference & odometer for bike 2. a. Dual Odometer (Settable) When “00000” shows & blinks press L & R buttons at the same time, the last two digits will flash. Advance them rapidly by holding down the R 2. Installing/Replacing the battery. Remove the battery cover by using a narrow flat blade or similar opener as illustrated in fig. 2. Insert a new battery (3v) CR2032, position the (+) pole upward as illustrated. Place the battery properly into the case and close the cover securely. After the battery is installed fig 2 button, or one at a time by pressing the R button. When desired number has been achieved press both L & R buttons for confirmation and the next three digits will flash. Repeat the same method to complete. Press both L & R buttons to confirm and enter “ODO” function. If “ODO” program is not necessary, press L or R for next function setting. Note: Dual Odometer function is used for 2 bikes separate odometers. Bike 1 & bike 2 have their own Odometer record. (The maximum distance of the odometer is 9,999 speed scale and wheel size can be set. km or 6,213 mi. ) fig 3 Go to ( ODO) Odometer function, press both L & R buttons at same time to After installing the battery, all displays will be review display wheel-circumference value ( will last for 3 seconds) when illuminated, the “SEL km” will remain on the screen needed. as in fig 3. Press either the Left ( L) or Right (R) 3. Setting Speed Scale Choose KM for Kilometers b. Review wheel-circumference value or MI for Miles. Page 2 Page 3 c. Bike 1 or 2 selecting & resetting the wheel-circumference value When you are in wheel-circumference value review mode, press L or R button to select bike 1 or 2. For wheel-circumference resetting, press L & R at the same time again until the last two digits blink. Repeat steps as above ( point 4) to reset the wheel circumference as your bike. This convenient design is handy for switching between different size bike tires. 5. Setting clock time Under any display mode except Stopwatch, press R button for 1 second. Clock time displayed. Repress either L or R button to return to “Odometer ( ODO)” mode. Follow step 2 to complete setting clock time and 12/24 hour alternate. a. 12/24 hours alternative. When clock is displayed, press both L & R buttons at the same time. Clock will blink then press L or R button to switch between 12 hours and 24 hours. To reset clock, press L & R at the same time ( as following b.); after 3 seconds, clock will stop blinking automatically. b. Resetting clock time After choosing 12 or 24 hours, press L & R at the same time, minutes “MM” will blink (fig. 5). Advance them rapidly by holding the R button, or one at a time by pressing the R button (t...