Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
¦ We recommend the hood be installed 30"–36" (76.2 cm – 94.1 cm) above the countertop. ¦ Check your ceiling height and the hood height maximum WARNINGExcessive Weight Hazard Use two or more people to move and install range hood. Failure to do so can result in back or other injury. before you select your hood. 3. Using 2 or more people, lift range hood onto protective covering. WARNINGExcessive Weight Hazard Use two or more people to move and install range. Failure to do so can result in back or other injury. 4. Determine and mark the centerline on the wall where the canopy hood will be installed. 5. Select a mounting height between 30" and 36" (76.2 cm and 94.1 cm) above the range to the bottom of the hood and mark reference line on the wall. NOTE: For installation locations with reduced ceilings heights, the vent hood may be installed using the upper vent cover for both vented and non-vented (recirculating) installations. 1. If possible, disconnect and move freestanding or slide-in range from cabinet opening to provide easier access to rear wall. Otherwise put a thick, protective covering over countertop, cooktop or range to protect from damage or dirt. 6. Tape template in place aligning the template centerline and bottom of template with hood bottom line and with the centerline marked on the wall. A B B CD A. Centerline B. Mounting hook location C. Fastener locations D. Mounting height reference 7. Mark centers of the 6 fastener locations through the template to the wall. IMPORTANT: At least two of the screws must be installed into wood. Remove the template. 8. Drill ...." (2.75 mm) pilot holes at all locations where screws are being installed into wood. 9. Determine and make all necessary cuts in the wall for the vent system. Install the vent system before installing the hood. See “Venting Requirements” section. 10. Determine the required height for the ..." conduit and drill a 1..." (3 cm) hole at this location. 11. Run wire through the ..." conduit according the National Electrical Code or CSA Standards and local codes and ordinances. There must be enough ..." conduit and wires from the fused disconnect (or circuit breaker) box to make the connection in the hood’s electrical terminal box. 12. Use caulk to seal all openings. NOTE: Do not turn on power until installation is complete. 13. Attach 2 mounting hooks to the wall at locations marked on the template. A B A. Mounting hooks B. Centerline on wall Vent Cover Support Bracket Installation Installations using telescoping upper and lower vent cover assembly. 1. Position vent cover bracket on wall about ..." (3 mm) away from the ceiling. 2. Mark the hole locations. 3. Drill ..." (9.5 mm) holes for wall anchors and insert anchors flush with the wall. A B A. Vent cover support bracket B. Centerline on wall 4. Attach vent cover support bracket to wall. Installation locations with reduced ceiling heights. For vented and non-vented (recirculating) installations, the vent hood is installed using the upper vent cover (26" [66.0 cm]) plus a ..." (6.4 mm) thick wood filler. 1. For the vent cover to slide down and engage the top of the hood, the vent cover bracket must be installed ..." (6.4 mm) below the ceiling. 2. The remaining space above the vent cover can be filled with a ..." (6.4 mm) thick piece of plywood cut to the inside cross section of the chimney cover and finished to match the ceiling. 3. Cut the self-adhesive rubber tape supplied with the hood in 4 identical pieces. Attach two pieces of tape to each side of the support bracket. A A. Rubber tape Vent Installations Vented installations Install transition on top of hood (if removed for shipping) with 2 sheet metal screws. Non-vented (recirculating) installations 1. Install transition on top of hood (if removed for shipping) with 2 sheet metal screws. 2. Attach the vent cover ceiling bracket to the deflector with two screws provided. B A. Vent cover support bracket B. Deflector A 3. Connect the deflector to the transition with 6" (15.2 cm) round vent. Install Range Hood Make Electrical Connection WARNINGExcessive Weight Hazard Use two or more people to move and install range hood. Failure to do so can result in back or other injury. 1. Hang hood on 2 mounting hooks through the rectangular cutouts on back of hood. B B D C A, Mounting hooks B. Mounting screws C. Leveling screws D. Centerline on wall A 2. Level the hood with leveling screws in mounting hooks or rectangular cutouts, using a level across bottom of hood. 3. Secure hood with 4 screws through remaining 4 holes in hood. Install Vent (for vented installations only) 1. Fit vent system over transition piece. A A. Transition 2. Seal connection with duct tape. WARNINGElectrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. 1. Disconnect power. 2. Remove terminal box cover. 3. Remove the knockout in terminal box cover and install the UL-or CSA-l...