Assessments - , GPA:
(
)
)
Fabricante : Casablanca Company
Arquivo Tamanho: 1.12 mb
Arquivo Nome : 1018b0de-3024-4966-9afc-0021a6418c75.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
Using Existing Ceiling Fixture Outlet Box After turning the power OFF at its source (either circuit breaker or fuse box), lower the old fixture and disconnect the wiring. Check the ceiling fixture outlet box to be sure that it is marked ‘Approved for ceiling fan mounting’. If it is not, a new box must be installed. CROSSBAR MOUNTING BRACKET INSTALLATION WARNING: Damp Location rated fans require a Ground Fault Interrupter (GFI). Use a weather-proof outlet box, properly connect ground wires, and use only under a weather-proof structure. Proceed with installation as follows: Step 1. Route the wires from the ceiling outlet box through the crossbar mounting bracket center hole. Attach the bracket, with ground wire and ridges down, to the ceiling fixture outlet box with the mounting hardware included with the outlet box. Using the screwdriver, tighten the screws firmly by hand only, being careful not to bend the bracket by over tightening. CAUTION: To reduce the risk of personal injury, use only the mounting hardware provided with the approved outlet box to install the crossbar mounting bracket. CEILING FAN APPROVED OUTLET BOX RIDGE SIDE CROSSBAR DOWN MOUNTING BRACKET CEILING WIRING FLAT WASHER GREEN GROUND WIRE OUTLET BOX MOUNTING HARDWARE CANOPY HARDWARE CANOPY SCREW (4) CANOPY CANOPY LOCK WASHER (4) HATCH CANOPY 4 CANOPY INSTALLATION ESTRADA CANOPY INSTALLATION ESTRADA Step 2. Thread the wires from the ceiling through the opening in the canopy. Attach the canopy to CROSSBAR MOUNTING the crossbar mounting bracket with three of the BRACKET INSTALLED 8-32 x 21/4. long canopy screws and canopy lock washers. Using the screwdriver, tighten the screw firmly by hand only. CANOPY LOCK WASHERS CANOPY SCREWS CANOPY Note: On sloped ceilings, align the canopy opening toward the top or room peak. HANGING THE FAN Step 3. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. Check that no wires were pinched. Rotate the fan body until the slot in the ball fits into the pin opposite the canopy opening. Step 4a. Attach the fan wires to the ceiling fixture outlet box wiring by placing the bare ends of the wires side by side and then securing with a wire nut. Test that the connection is secure by pulling on the wire nut. Connect in this order: Step 4b. Pull Chain Connections • GREEN leads from mounting plate and fan to GROUND conductor of power source. Secure with wire nut. • WHITE wire from fan to white NEUTRAL wire in ceiling fixture outlet box. Secure with wire nut. • BLUE wire and BLACK power wire from fan to BLACK power wire in ceiling outlet box. Secure with wire nut. CAPPED BLUE D1-OPTION WIRE. PIN SLOT BALL CANOPY ELECTRICAL CONNECTIONS 2 BLACK WIRES 2 WHITE WIRES WIRE NUT 3 GREEN WIRES 5 CANOPY HATCH INSTALLATION ESTRADA CANOPY HATCH INSTALLATION ESTRADA Step 5. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires are clear of the canopy opening. Step 6. Install canopy hatch with the last canopy screw and lock washer. To do this, tilt the fan body away from the hatch opening. Using the screwdriver, tighten the screws firmly by hand only, Step 7. Straighten the fan, then check to ensure that there is no movement between the canopy and ceiling or Hang-Tru ball and top support shaft. CANOPY HATCH CANOPY SCREW LOCK WASHER Note: Write down the Serial Number and the model number for future reference. TILT THE FAN TO INSTALL LAST CANOPY SCREW BLADE TO BLADE HOLDER INSTALLATION BLADE & BLADE HOLDER HARDWARE BLADE SCREW (4 PER BLADE) BLADE HOLDER HOLDER BLADE SCREW RUBBER GROMMET (2 PER BLADE) (4 PER BLADE) BADGE RUBBER GROMMET INSTALLATION Step 8. Insert a rubber grommet through each blade hole of every blade. Inspect both sides of the blade to assure that the lips of the grommet are fully engaged. CORRECT INSTALLATION INCORRECT INSTALLATION 6 ESTRADA BLADE INSTALLATION Step 9. Attach the blades to the blade holders by first pressing the blade badge into the blade, then installing the blade holder using the four blade screws provided for each blade. Using the screwdriver, tighten securely by hand. BLADE SCREW (4 PER BLADE) BLADE BADGE STYLE BLADE HOLDER BLADE BADGE REMOVE SHIPPING BLOCKS Step 10. On the flywheel remove the five SHIPPING shipping blocks by unscrewing the screws. BLOCKS Set these screws aside for installing the blades in Step 11. Discard the five shipping blocks. BLADE/BLADE HOLDER INSTALLATION Step 11. Using the five screws removed in Step 10, and the five additional screws from the pack, attach each blade/blade holder assembly to the motor. Using the screwdriver, tighten securely by hand only. 7 3-SPEED OPERATION 3-SPEED OPERATION Pull-chain switches on the fan control the fan and reverse. REVERSE FAN & SPEED Using the fan control pull-chain switch: Fan off at start. First pull: fan ON, low speed Second pull: medium speed Third pull: high speed Fourth pull: fan OF...