Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise. Note: Bulb does not unscrew; it turns 60 degrees, stops and falls out. If bulbs are difficult to turn due to prolonged use, firmly attach a glass suction cup approximately the diameter of the bulb or use a rubber/latex glove and turn counter clockwise. Replacement bulbs are available at specialty lighting stores. Purchase type MR16 (GU-10) 35W halogen. For Zephyr part numbers please turn to page 19 of the manual. Bottom View Maintenance Lights 17 Troubleshooting TROUBLESHOOTING PROCEDURES FOR TORNADO II AND TORNADO III Issue Cause What to do After installation, the unit doesn’t work. 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s power is ON. 2. The power line and the cable locking connector is not connecting properly. 2. Check the power connection with the unit is connected properly. 3. The switch board and control board wirings are disconnected. 3. Make sure the wirings between the switch board and control board are connected properly. 4. The wires on control board are loose. 4. Make sure the wires on the control board are connected properly. 5. The switch board or control board is defective. 5. Change the switch board or control board. Light works, but motor is not turning. 1. The motor is defective, possible seized. 1. Change the motor. 2. The thermally protected system detects if the motor is too hot to operate and shuts the motor down. 2. The motor will function properly after the thermally protected system cool down. 3. Damaged capacitor. 3. Change the capacitor. 4. The motor wire is not connected. 4. Make sure the motor wire is plugged into the molex connector. The unit is vibrating. 1. The motor is not secure in place. 1. Tighten the motor in place. 2. Damaged blower wheel. 2. Change the blower. 3. The hood is not secured in place. 3. Check the installation of the hood. The motor is working, but the lights are not. 1. Defective halogen bulb. 1. Change the halogen bulb. 2. The light bulb is loose. 2. Tighten the light bulb. 3. The wires on the control board are loose. 3. Make sure the wires on control board are connected properly. The hood is not venting out properly. 1. The hood might be hanging too high from the cook top. 1. Adjust the distance between the cook top and the bottom of the hood within 26” and 36” range. 2. The wind from the opened windows or opened doors in the surrounding area are affecting the ventilation of the hood. 2. Close all the windows and doors to eliminate the outside wind flow. 3. Blockage in the duct opening or duct work. 3. Remove all the blocking from the duct work or duct opening. 4. The direction of duct opening is against the wind. 4. Adjust the duct opening direction. 5. Using the wrong size of ducting. 5. Change the ducting to correct size. Filter is vibrating. 1. Filter is loose. 1. Adjust or change the filter. 2. Spring clip is broken inside filter opening 2. Change the spring clip. RF Remote control does not work 1. Battery is dead 1. Replace battery with type A23 12v 2. Poor communication with the power pack 2. Remote control must be within 15 ft of power pack 3. RF remote lost communication with power pack 3. Reset power pack and remote by switching power off at the circuit breaker for 5 minutes. Pace remote on counter top near power pack and switch the circuit breaker back on. The blower turns on by itself. 1. The clean air function has been enabled turning the blower on every 4 hours. 1. Disable the clean air function by following the steps on page 14. 18 DESCRIPTION PART # Replacement Parts Light Bulb MR16 (GU10) 35W (each) Z0B-0023 Baffle Filter (each) 50210010 Remote Control 14000005 Optional Accessories Liner,36” (AK8200AS) AK0806AS Liner,42” (AK8200AS) AK0842AS Liner,48” (AK8300ASX) AK0848AS Liner,54” (AK8300ASX) AK0854AS Liner,60” (AK8300ASX) AK0860AS To order parts, visit us online at or call us at 1.888.880.8368 List of Parts Accessories 19 1-888-880-8368 STAPLE YOUR RECEIPT HERE TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call: Limited Warranty Proof of the original purchase date is needed to obtain service under warranty 1-888-880-8368 STAPLE YOUR RECEIPT HERE TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call: Limited Warranty Proof of the original purchase date is needed to obtain service under warranty Zephyr Corporation (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you” or “your”) of Zephyr products (the “Products”) that such Products will be free from defects in materials or workmanship as follows: Ten Year Limited Warranty for Parts: For ten years from the date of your original purchase of the Products, we will provide, free of charge, Prod...
Este manual também é adequado para os modelos :Fans - AK8300ASX (400.88 kb)