Assessments - 5, GPA: 4
(
)
)
|
Facilidade de uso
Internal and in-line blowers require a roof or wall cap (not provided). Connect ductwork to the cap and work back towards the hood liner. Use sheet metal screws and aluminum tape or high temperature duct tape to seal joints between ductwork sections. All pro hood liners include a backdraft damper in the tran- sition assembly. Local codes may require the use of an additional backdraft and/or make-up air damper. Contact your local HVAC professional for specific requirements. Backdraft and make-up air dampers are available through your authorized Wolf dealer. For local dealer information, visit the find a showroom section of our website, wolfappliance.com. PRO HOOD LINERS DUCTWORK INSTALLATION THROUGH ROOF 12" (305) LINER HEIGHT 12" (305) 4" (102) DECORATIVE HOOD FOR 191/4" 31" (787) TO 36" (914) FOR 221/2" 30" (762) TO 36" (914) 191/4" (489) LINER DEPTH 221/2" (572) LINER DEPTH Pro Hood Liner Installation Wall Preparation Minimum 2" (51) x 4" (102) lumber is required to construct wall framing. Refer to the illustration below for mounting hole locations and a cross-section view of a typical instal- lation. Framing must be able to support the weight of the hood and internal blower, if applicable. DECORATIVE HOOD 23/4" 2" (51) (70) #10 x 2" (51) SCREW 8" 4" (102) (203) Mounting hole locations. Installation cross-section. Hood Liner Preparation IMPORTANT NOTE: Remove all packaging material from hood liner and damper. Failure to remove material will obstruct airflow and significantly decrease performance. 1) To remove filters, press upward then rotate bottom outward. Refer to the illustration below. To aide in removal, remove center filter first. Gloves should be worn when handling filters. 2) The damper is packaged inside the hood liner in a separate box. Remove damper from box and place it on top of the hood liner using the hold-down brackets. 3) Secure hold-down brackets to damper flange with screws provided. Refer to the illustration below. 4) Seal with aluminum tape or high temperature duct tape. 5) Connect damper to duct using sheet metal screws and aluminum tape or high temperature duct tape. Verify screws do not affect the operation of the damper. HOLD-DOWN BRACKET SPRING LOWER DAMPER CHANNEL FILTER SIDE VIEW Filter removal. Mount damper. Pro Hood Liner Installation wolfappliance.com/specs Hood Liner Installation Position the hood liner in the desired location. Insert #10 x 2" (59) screws through the mounting holes on the back plate. Verify the screws engage two wall studs or blocking. If additional support is required, drill supplementary holes through the back plate and secure with screws. Electrical Connection Before making electrical connections, make sure the electrical power is turned off at the service panel. IMPORTANT NOTE: Refer to specific installation instruc- tions provided with each blower assembly for additional mounting and wiring instructions. 1) Remove the electrical box cover from inside the hood liner. Insert Romex® from service panel (and Romex® from in-line or remote blower, if applicable) through the back of the hood liner and into the electrical box. Secure with an appropriate electrical connector. Refer to the illustration below. 2) Use wire connectors provided to connect black to black, white to white and green to green/bare wire. For in-line and remote blowers, attach the cord assembly to Romex® from the blower. 3) Place all wiring connections inside the electrical box and reinstall electrical box cover. Verify all wires are secure and not pinched between cover. 4) Insert cord assembly plug into hood liner receptacle. Refer to the illustration below. Turn on power and check operation. ELECTRICAL BOX (INSIDE HOOD) RECEPTACLE (INSIDE HOOD) Location of electrical box. Location of receptacle. Pro Hood Liner Installation Complete the Installation FILTER INSTALLATION To install filters, press upward then rotate bottom outward. The filter vanes should be placed perpendicular to the front of the hood. Refer to the illustration below. To aide in removal, remove center filter first. Gloves should be worn when handling filters. LIGHT BULB INSTALLATION A suction-cup-style light bulb changer is provided with pro hood liners. Use the changer to push the bulb into the receptacle and rotate counterclockwise one-quarter turn. Refer to the illustration below. FILTER SIDE VIEW SPRING LOWER CHANNEL LIGHT BULB CHANGER Filter installation. Light bulb installation. Troubleshooting IMPORTANT NOTE: If the pro hood liner does not operate properly, follow these troubleshooting steps: • Verify electrical power is supplied to the appliance. • Verify all packaging material has been removed. • If the appliance does not operate properly, contact Wolf factory certified service. Do not attempt to repair. Wolf is not responsible for service required to correct a faulty installation. Service Information Service Information If service is necessary, maintain the quality built into your pro hood liner by contacting Wol...
Este manual também é adequado para os modelos :Fans - L402212 (126.5 kb)