Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
Tighten mounting screws securely. A long screwdriver works best. Replace bottom cover. DUCT TAPE Connect ductwork to hood. Use Duct Tape to make joints secure and air tight. PAR20, 50W MAX. HALOGEN BULB (2) - or -R16, 40W MAX. INCANDESCENT BULB (2) fH Install (2) PAR20, 50 W Maximum Halogen Bulbs or (2) R16, 40 W Maximum Incandescent Bulbs. Purchase bulbs separately. nk CAUTION: Bulbs may be hot! Refer to bulb packaging for further information. 5 | Replace filters, turn on power at service panel, and test for proper operation. NuTbne NON-DUCTED FILTERS If hood is to be installed Non-Ducted: Purchase a set of (2) Non-Ducted Filters from your local distributor or retailer and attach them to the aluminum mesh filters. NOTE: For models that are installed in the non-ducted mode, the most effective operation is achieved at speeds 1 and 2. These speeds provide the most efficient and quiet operation during cooking, while maximizing the benefits of the recirculating filtration system. ALLURE® WS2 SERIES RANGE HOOD Page 6 OPERATION Fan and Lights: 3 push button switches for each. Push any button to select one of 3 fan speeds or one of 3 light levels. Push the same button to turn fan or light off. Press another button to change fan speed or light level. A light above each fan button indicates the fan speed. Heat Sentry: Your range hood is equipped with the Heat Sentry feature, which monitors temperature. The Heat Sentry will automatically turn the fan on at its highest speed when the temperature is above normal. 1) If a fan setting is selected when the Heat Sentry in on, the light above the fan button will flash on and off. 2) If the fan setting is off when the Heat Sentry is on, the light above fan button 3 will flash on and off rapidly. After the temperature has lowered to normal, the fan will change to the setting prior to the Heat Sentry turning on. Fuse: The hood control contains a fuse to protect it from power surges. If the fuse has opened (blown), the green fan-level indicators will operate properly when the fan buttons/switches are pressed - but the fan and lights will not turn on. The fuse is a 5 x 20 mm, 10 Amp, Fast-Acting, 125V (min.). Common manufacturer and part numbers are: Littlefuse, 217010; Bussmann, GMA10A; Wickmann, 1942100. Radio Shack, Digikey (1-800-344-4539), and most electronic supply stores have them in stock. To replace the fuse: 1. Disconnect power at service entrance. 2. Remove filters, bottom panel, light wire harness, and air chute. 3. Remove and inspect fuse. If it is not open (blown), additional diagnostics need to be done. 4. Install new fuse. 5. Re-assemble air chute, light wire harness, bottom panel, and filters. 6. Turn on power and check hood/control operation. CLEANING_ A WARNING: To reduce the risk of electric shock, disconnect from power supply before cleaning. Aluminum mesh filters: Clean frequently using hot water and a mild detergent. Filters are dishwasher safe. Charcoal filters: Clean filter surfaces frequently with a damp cloth and a mild detergent. DO NOT immerse filters in water or put in dishwasher. The special “Clean Sense” feature indicates when the filter is to be replaced. The blue and yellow strips will blend to green when it is time to change the filter. The “Clean Sense” feature works best when facing toward the cooking surface. To clean hood: Remove filters. Use a damp cloth and a mild detergent to wipe all grease-laden surfaces. Do not use abrasive cloth, steel wool pads, or scouring powder on the Teflon®-coated bottom cover or on any painted surface. Use care when cleaning blower wheel - it must not become bent or misaligned. DO NOT ALLOW WATER TO ENTER MOTOR. Make sure all surfaces are completely dry before re-installing filters and restoring power. Motor is permanently lubricated. Do not oil or disassemble motor. Teflon® is a registered trademark of DuPont. NuTbne ALLURE® WS2 SERIES RANGE HOOD SERVICE PARTS KEY NO. PART NO. DESCRIPTION 1 R680508 7” Round Duct Plate (includes hardware) 2 R740013 Damper/Duct Connector (includes hardware) 3 R602017 Screw, #8-18 x % Hex* (2 in package) 4 R334755 Motor Capacitor (includes wire nuts & hardware) 5 R501031 Isolation Transformer 6 R627521 Nameplate, White R627522 Nameplate, Almond R627523 Nameplate, Black R627534 Nameplate, Biscuit 7 R169005 Control Panel, White (includes Key No. 6 & hardware) R169006 Control Panel, Almond (includes Key No. 6 & hardware) R169007 Control Panel, Black (includes Key No. 6 & hardware) R169008 Control Panel, Biscuit (includes Key No. 6 & hardware) 8 R601535 Screw for Plastic, #6 x / Flat Hd. (3 in package) 9 R602534 Screw, #8-18 x 3/8 (2 in package) 10 R602533 Ground Screw 11 R680505 Scroll Cover, Outlet (includes hardware) 12 R680507 Scroll Cover, Front (includes hardware) 13 R111663 Control Assembly (includes Key Nos. 6, 7 & hardware) 14 R401647 Air Chute Assembly (includes Key No. 15 & hardware) 15 R4016...