Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. I B23 Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. B25 Turn on the power source. ON OFF B26 B24 J Test the motor. If the motor does not run, check the plug connection. Secure the motor by tightening the 2 screws. 023_41953_EngS_2-15-08.indd 10 2/16/08 12:25:36 PM C12EFExisting Construction – accessible from above EXISTING FAN C11 NO EXISTING FAN 9”9.75” ORRemove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (9”x 9.75”). Cut out an opening for the housing. Use the motor housing as a template to mark position. Slide the mounting rails into brackets. 5/81/25/81/2C13C14 position the correct depth mark at the bottom edge of the Mark position of screws by using holes as a template. joist based on the thickness of your sheetrock. 11 41953-01 02/15/2008 023_41953_EngS_2-15-08.indd 11 2/16/08 12:25:37 PM 41953-01 02/15/2008 12 C17 C18 C19 C20 C15 C16 Drill a hole in the center of each outline. Insert screws, leaving space between the screw head and the joist. Screws are not provided. Attach the rails onto the screws. Tighten screws. Connect 4” duct and vent to the outside. Tape joints. If ducting does not fit securely, an adapter may need to be purchased. Route wires through the strain relief. 023_41953_EngS_2-15-08.indd 12 2/16/08 12:25:38 PM 41953-01 02/15/2008 13 C21 Tighten the strain relief screws. A 3 Pin 2 Pin Fan Motor Light Light Green Black Black Red Red White Black Black White White Bare Copper Ground Night Light Night Light Switch 1 (AC In) Main Switch 1 (AC In) *Option Fan & Main Light Together Switch 2 (AC In) *Option C22 Connect wires as shown. C24 I H C23 G Install the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover plate. Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. 023_41953_EngS_2-15-08.indd 13 2/16/08 12:25:39 PM 41953-01 02/15/2008 14 C25 I C26 J C27 ON OFF C28 Secure the motor by tightening the 2 screws. Turn on the power source. C29 E1 Go to step on page 17 to attach grille. Test the motor. If the motor does not run, check the plug connection. Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. 023_41953_EngS_2-15-08.indd 14 2/16/08 12:25:41 PM 41953-01 02/15/2008 15 D11 EXISTING FAN F D12 Existing Construction – accessible only from below D13 2 1 D14 Route wires through strain relief. Remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (9”x 9.75”). Move the housing into position above the ceiling. Attach existing ducting to duct connector. Tape joints. If ducting does not fit securely, an adapter may need to be purchased. F D15 Install the housing flush with the sheetrock and secure by tightening the pre-loaded screws into the joist. 023_41953_EngS_2-15-08.indd 15 2/16/08 12:25:42 PM 41953-01 02/15/2008 16 I D18 I D19 D20 J Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. Secure the motor by tightening the 2 screws. A 3 Pin 2 Pin Fan Motor Light Light Green Black Black Red Red White Black Black White White Bare Copper Ground Night Light Night Light Switch 1 (AC In) Main Switch 1 (AC In) *Option Fan & Main Light Together Switch 2 (AC In) *Option D16 Connect wires as shown. H D17 G Install the wiring cover plate. 023_41953_EngS_2-15-08.indd 16 2/16/08 12:25:43 PM 41953-01 02/15/2008 17 ON OFF D22 D23 E1 Go to step on page 17 to attach grille. D21 Test the motor. If the motor does not run, check the plug connection. Turn on the power source. E2 O M P N F E1 Attaching the Grille Remove the thumbscrews. Remove glass dome. 023_41953_EngS_2-15-08.indd 17 2/16/08 12:25:44 PM 41953-01 02/15/2008 18 E4 K M N E6 E7 E8 O Position the strain relief bracket between the plugs as shown, and screw into place. Attach thumbscrews. WARNING: To reduce the risk of electrical shock, all 4 thumbscrews MUST be properly installed. Install 2 Max 60 Watt A15 bulbs (Not Included). Align glass dome and push up. E3 M Connect wiring harness. DO NOT ALLOW THE FIXTURE TO HANG FROM THE WIRING HARNESS. E5 M Align posts A, B, C and D (stamped into motor housing) with posts A, B, C and D (stamped into light fixture). Slide light fixture over posts. 023_41953_EngS_2-15-08.indd 18 2/16/08 12:25:46 PM E9P Screw glass dome into position. Trouble Shooting problem: Fan does not come on. Solution: • Hunter Fan Bath Ventilators are extremely quiet. To confirm that the fan is running, place your hand near the vents to feel the air movement. • Turn power on, replace fuse, or reset breaker. • Check all plug connections to be sure t...
Este manual também é adequado para os modelos :Fans - 41953-01 (8.42 mb)