Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
2a; then holding it against the wall to ensure that it is correctly positioned mark the holes for the top fixing screws on the wall. • Pilot drill the wall using an 8 mm drill and fix the splashback using the 8 mm rawl plugs and screws supplied. • If the fixing holes in the bottom of the splashback are not to be used to secure the splashback to the wall the installer should ensure that the bottom edge is tucked down behind the rear of the worktop. Fixing the canopy hood • Adjust the two screws V (on the canopy connection points) to approximately half way. • Hook the rear of the canopy to the wall bracket 1, after anchoring the latter to the wall. • Turn the screws V to adjust the canopy vertically and level it horizontally. • Fit and lock the central fixing screw V1 (provided) to lock the canopy in place (fig.3). Fig. 3 6 GB 0 0 0 0 0 0 0 0 0 0 aaaaaaaaaaaaaaaaaaaaaaaaaaaa0 aaaaaaaaaaaaaaaaaaaaaaaa0 aaaaaaaaaaaaaaaaaaaaa0 Ducting or Recirculation fitting Ducting fitting • The cooker hood can be ducted to the outside using either rigid or flexible fire retardant ducting of 120 or 150 mm. The choice is left to the installer. When 120 mm ducting is to be used it will be necessary to install the reduction flange item A on the air outlet fig. 4. • The installer should provide suitable ducting and sealing material for the installation. • The cooker hood can also be ducted to the outside through one of the rectangular openings located in either side of the lower section of the chimney stack. In this case the deflector (item D) should be fitted into the spigot (item R) to close the aperture which is not used (fig. 5). • If the hood is provided with the charcoal filters fitted, the filters should be removed (see paragraph Maintenance). Recirculation fitting • The filtered air is returned to the room through the two side grilles on U-shaped lower section I, which are either formed in the metal itself (fig. 6). • Fit the recirculation spigot item R into the round outlet on top of the canopy while pressing down on the spigot until it snaps into position. • Install the charcoal filters inside the canopy as instructed in paragraph Maintenance). Fig. 6 R A Fig. 4 243_A04 A R D 243_A05 Fig. 5 GB 7 0 0 0 0 0 0 0 0 0 0 aaaaaaaaaaaaaaaaaaaaaaaaaaaa0 8 a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a GB Electrical connection and working test • Before connecting to the mains supply ensure that the mains voltage corresponds with the voltage on the rating plate inside the hood. • Connect the cooker hood to the mains via a double pole switch which has 3 mm clearance between the contacts. • The appliance must be earthed. • Once the electrical connection has been completed, check that worktop illumination, motor and speed work properly. Fitting the telescopic chimney stack • Fit the two plastic supports provided to the top part of the hood. • To fit the upper section item S first expand the chimney slightly to allow it to fit over the wall brackets (item 2 fig. 1) and then secure the upper section using the 4 screws supplied. • The lower section item I of the chimney stack should be fitted between the lower bracket 2 and the wall. • Fix the U-shaped section to the plastic supports, using two of the screws provided in the bag of accessories (fig. 7). Part 2a OPERATION AND MAINTENANCE INSTRUCTIONS Fig. 7 S I GB 9 a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a USE Safety warnings • Before carring out any kind of maintenance or cleaning, disconnect the hood from the mains supply. • The grease filters and the charcoal filter should be cleaned or replaced as recommended by the manufacturer or more frequently if the hood is used consistently over 4 hours per day. • When using a gas hob in connection with the cooker hood never leave the burners of the hob uncovered while the hood is in use or when the pans have been removed. Switch off the gas before removing the pan, or for just short periods and never leave the hob unattended. • Always ensure that the flame is kept at the correct intensity to prevent the flame from licking round from the bottom of the pan; this will save energy and will avoid a dangerous concentration of heat. • Always ensure that the appliance is used in accordance with the manufacturer’s instructions for the removal of contaminated air and odours during cooking. Instruction for Use Control panel BUTTON T1 = Turns the lighting system on and off; BUTTON T2 = Turns the on and off at low speed. This is ideal to obtain a particularly silent but continuous flow of air when the level of cooking fumes is low; BUTTON T3 = Medium speed, suitable for most normal operating conditions. This gives ...
Este manual também é adequado para os modelos :Fans - HI561 IXUK (427.28 kb)