Assessments - , GPA:
(
)
)
Fabricante : Fujioh
Arquivo Tamanho: 357.45 kb
Arquivo Nome : BUF-01A_02A_(1U03_2384).pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
e) This unit is designed for ducted or ductless installation. When ductless kit part numbers FDK-02A is installed, this unit is certified ductless. The end user is responsible to ensure compliance with all Federal, State and Local Environmental and Fire codes. 2 The range hood unit must be mounted to a liner which has the following dimensions. Install the liner securely after checking that the opening size of the liner is the same as the figure below. • If the range hood is not installed properly, it could become detached and fall. • Ensure that the metal duct does not touch other metal housing materials, otherwise fire or electric shock could result. • When the liner is installed in the wooden hood, the inside of the wooden hood placed above the cooking surface must be fully covered by the metal barrier including bottom edges. Select a suitable liner and metal barrier according to the size and shape of the wooden hood and install properly. • The liner should be installed tightly. If the liner installation is not correct, the range hood unit may become detached and fall. • Wear working gloves to avoid injury. CAUTION: 5. Explanation to the End User (1) Referring to the Operation Manual, explain the operation of this range hood to end users. (2) The Installation Manual and Operation Manual should be given to the end user. 1 Assembly (1) Replace the front cover with 4 screws. To prevent the screw holes from being damaged, be sure not to over tighten the screws (with the torque of 13 inch-lbs. [1.5 N-m] or less). (2) One 50Watt halogen light bulb (not supplied) can be mounted in this range hood. Prior to function check, install light bulb (Bulb type standard MR16-GU10), rated 120V - 50Watt or below. The following light bulbs are recommended for this range hood. • GE Model No. Q50GU10/FL/CD • PHILIPS Model No. Twistline 50W GU10 120V MR16 Turn the lamp clock-wise to install. 2 Check (1) Turn on the electrical circuit to the range hood. (2) Make sure that the switch and light operate correctly. Refer to page 5 of the Operation Manual. (3) Make sure that the range hood has no abnormal noises and/ or vibration. • Electrical wiring should be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction. An unqualified person doing the work could result in fire, electric shock or injury. • This range hood uses 120V AC. Do not connect to other voltage since fire, electric shock or damage could result. Be sure to switch power OFF at service panel before wiring. 3 Connect the electrical wires as follows: Connect wires tightly and securely using wire connectors (not supplied). 3 Make the duct joint secure and air tight using non-flammable tape such as duct tape, etc. (not supplied) Note: Make sure that the shutter installed in the exhaust pipe moves freely. CAUTION: CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage. means prohibition. It indicates actions, if any, that mustn’t be done. 4. TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. 5. This unit must be grounded. CIRCUIT DIAGRAM 6. Check that the hood is correctly installed, since incorrect installation could result in the range hood becoming detached and falling off. 7. Connect only to an AC120 Volt power source or the range hood could result in fire, electric shock, and damage. DIMENSIONS CAUTION: WARNING: WARNING: 2 Align 4 screw holes of the liner and range hood unit, then fix securely using the supplied screws and nuts. Note: Fasten all the screws and nuts evenly. NAMES OF PARTS RANGE HOOD LOCATION 1 The range hood must be installed just above the cooktop. 2 The minimum distance from the cooking surface to the bottom of the range hood must be 24". 3 The total weight of the BUF-01A/02A range hood unit is 18 lbs. (8 kg) 4 Power requirements are: BUF-01A: AC120 V, 60 Hz, 1.5 Amp BUF-02A: AC120 V, 60 Hz, 2.1 Amp • Check that the hood is correctly installed, since incorrect installation could result in the detachment of the range hood and the unit could fall. CAUTION: ACCESSORIES Screw M5.30 Four (4) pieces Nut with plate Four (4) pieces 3 Run house wiring between service panel and hood location. 4 Prepare the range hood unit. (1) The range hood is supplied with the exhaust pipe fixed on its top plate. (2) Detach the tape stuck on the exhaust pipe. 3. TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a) Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including firerated construction. WARNING: 1U03 2384 • To reduce the risk of injury, keep your hands and other objects away from the fan while it is in motion. • Wear working gloves to avoid injury. CAUTION: Enclosure Switch Front cover Lamp (standard MR16-GU10, 50Watt) (not supplied) Filter 18-11/16" 6-11/16" 2-1/4" 2-1/4" 9-13/16" 5-1/2" 5-3/16" ...