Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. FOR YOUR SAFETY If you smell gas: • Do not try to light any appliance. • Do not touch any electric switch; do not use any phone in your building. • Immediately call your gas supplier from your neighbors phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. • Open windows / Extinguish all flames. Homeowner’s Installation & Operating Manual CERTIFIEDDESIGNCERTIFIED PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE 51810 1/06 Rev. 2 Majestic® Fireplaces Power Venting System Installation Instructions General information and instructions for the power vent system model No. PVS-1. NOTE: The PVS-1 will only work in conjunction with a VN Gas Valve P/N 57588 or VP Gas Valve P/N 57587. 1. This power vent system must be installed by a qualified installer in accordance with all applicable local codes and with the current installation codes for gas burning appliances CSA-B149.1 in Canada or ANSI Z223.1/NFPA 54 in the U.S.A. Electrical connections and grounding must be in accordance with the Canadian Electrical Code, C22.1 Part 1 and in U.S.A., National Electrical Code ANSI/ NFPA70 and/or local codes where applicable. 2. This device must be installed by a qualified professional installer in accordance with these instructions. If improperly installed, a hazardous condition such as an explosion or carbon monoxide poison could result. 3. The Power Vent System #PVS-1 has been certified by CSA to be installed as a component part and is for use only with fireplace models listed in the front page of this manual. Certification is cancelled if used with other than listed products. 4. Plan the vent system so that code required distances are maintained from plumbing and wiring. 5. The Power Venter motor shaft must be mounted horizontally to ensure proper operation of the fan pressure proving switch and to prevent motor bearing wear. 6. Flue gas temperatures must not exceed 470.F at Power Venter inlet. Ambient temperature must not exceed 104.F. 7. Disconnect power supply when making wiring connections or when working around the fan blade and motor. Failure to do so may result in severe personal injury and equipment damage. 8. Make certain the power source is adequate for the fan motor requirements. Do not add the Power Venter to a circuit where the total load is unknown. 9. This Power Venter System #PVS-1 shall be installed with Sound Reducer Kit Nos. SR 4 for fireplaces with a 4” (102 mm) flue collars and SR 5 for fireplaces with 5” (127 mm) flue collars. See INSTALLATION RESTRICTIONS Page 5. Power Vent System Parts and Description 1. Fan Assembly - comes complete with 6’ (1.8 m) power cord for plugging into a standard house receptacle. The system is completely pre-wired and includes the pressure switch and 24 volt transformer. 2. 24 Volt Wiring Harness - a 40’ (12m) wiring harness with plug-in connectors. Eliminates costly time consuming electrical installations. 3. Vent Terminal - the device which exhausts flue gases into the atmosphere. 4. Fan Mounting Bracket - to secure the fan in a vibration- free mode so as to reduce vibration through the pipes. 5. Flex-Connector - an additional device to reduce vibration and noise through the pipes. It is mounted to the negative inlet side of the fan. 6. Approved 4” (102 mm) diameter insulated aluminum flex liner, 4” (102 mm) diameter B-Vent* or 4” (102 mm) diameter single wall metal vent connector. 7. Assorted clamps, connectors and wall mounting brackets. General Venting Information Always consult your local codes and authorities, in the absence of such codes, follow the current installation codes for gas burning appliances CSA-B149.1 in Canada or ANSI Z223.1/NFPA 54 in the US. 1. Clearance to Combustible Materials: • 1” (25 mm) for insulated single wall vent or flexible vent pipe. • 6” (152 mm) for single wall fan housing. • 1” (25 mm) for fan motor. • 1” (25 mm) for B-Vent.* • 6” (152 mm) for single wall vent or flexible vent pipe. * B-Vent can only be used on the negative side of the power venter - between the appliance and the power venter - and insulated flexible liner or single wall vent on the outlet side of the power venter. To reduce fan noise or condensation, CFM Corporation recommends all venting pipes be insulated with a minimum of 1” (25 mm) fiberglass insulation. 2. Total allowable system length is 100’ (30 m) of straight pipe. Minimum allowable system length is 5’ (1.5 m). NOTE: Deduct 10’ (3 m) for each 90° elbow and 5’ (1.5 m) for each 45° elbow. Example: An installation requires 30’ (9 m) of straight pipe with 45° and three (3) 90° elbow. Straight pipe 30’ (9 m) 45. Elbow (1) 5’ (1.5 m) 90. Elbow (3) 30’ (9 m) TOTAL 65’ (19.5 m) Total equivalent pipe length = 65’ (19.5 m) 2 51810 3. Vent System Termination Before installing Power Venter, determine location of vent system termination. 4. Location of the F...