Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
. . . . . )%. . . . . . . . . . %%). . . !. +. %, . -&.&/.%%. . % . ). 0'.//1.%%. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Merloni Elettrodomestici UK Ltd., Morley Way , Peterborough, PE2 9JB 2 UK ! It is important to conserve this booklet for consultation at any moment. In the case of sale, cession or move, make sure it is together with the product. ! Read the instructions carefully: there is important information about installation, use and safety. ! Do not carry out electrical or mechanical variations on the product or on the discharge conduits. Installation Electric connection ! The power tension must correspond with the tension shown on the characteristics label situated inside the hood. If provided with a plug, attach the hood to a socket conforming to the regulations in force and placed in an accessible zone. If without a plug, (connected directly to the power supply), use a regulation bipolar switch with a distance of the contacts on opening not less than 3mm (accessible). ! If necessary, the situating of the supply cable must be carried out by the technical assistance service or a qualified person. ! An authorized installer must carry out the electrical connection of the hood. ! The company declines any responsibility whenever these regulations are not respected. Preliminary information for installation of the hood: Disconnect the hood during electrical connection, by turning the home mains switch off. Expansion wall plugs are provided to secure the hood to most types of walls/ceilings. However, a qualified technician must verify suitability of the materials in accordance with the type of wall/ceiling. The wall/ceiling must be strong enough to take the weight of the hood. Do not tile, grout or silicone this appliance to the wall. Surface mounting only. Do not fix chimney flue to furniture or fly over shelves unless the chimney flue can be easily removed, in case maintenance is ever required. Where foreseen remove the grease collecting panels. Remove the grease filter/s Do not tile, grout or silicone this appliance to the wall. Surface mounting only. Do not fix chimney flue to furniture or fly over shelves unless the chimney flue can be easily removed, in case maintenance is ever required. Assembling the chimney flue support/bracket (3 parts): The three parts should be fixed with 4 screws, the support extension is adjustable and should correspond to the internal width of the telescopic chimney flue. Assembling the deflector (only when a deflector composed of 3 parts is supplied – the deflector should be only for the filter version): The three parts should be fixed with 2 screws, the deflector extension is adjustable and should correspond to the width of the chimney flue support, to which it is then fixed. The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood must be not less than 50cm from electric cookers and 65 cm from gas or mixed cookers. If the instructions for installation for the gas hob specify a greater distance, this must be adhered to. 1.Draw a line corresponding to the centre line on the Installation wall to the ceiling with a pencil. It will help the K installation operations. 2.Apply the perforation diagram to the wall: The centre vertical line printed on the perforation diagram must correspond to the centre line drawn on the wall. In addition, the lower edge of the perforation diagram must correspond to the lower edge of the hood: keeping mind that the lower part of the hood, once installation is completed, must distance at least 50 cm from the cooking surface in case of electric plates and 65 cm in case of gas rings or mixed tops. 3.Place the support bracket on the perforation diagram making it coincide with the rectangle marked out. Mark the two external holes and make the holes. Remove the peroration diagram, insert two wall dowels and fix the support bracket of the hood with two 5x45mm screws. 4.Hang up the suction unit. 5.Adjust the distance of the suction unit from the wall. 6.Adjust the horizontal setting of the suction unit. 7. Mark the hole for definitively fixing the suction unit from inside the suction unit with a pencil. 8.Remove the suction unit from the bracket. 9.Make a hole at the marked point (O8mm - see operation 7). 10.Insert 1 wall dowel. 11.Apply flue support bracket „G“ to the ceiling, using the support bracket as a perforation diagram (the small slot on the support must coincide with the line previously traced on the wall – operation 1) and mark 2 holes with the pencil. Make the holes (O8mm) and insert 2 dowels. 12.Fix the flue support bracket to the wall with two 5x45mm screws. 13.Connect the suction group to the lower bracket. 14. Definitively fix the suction unit to the wall (COMPULSORY!!). 15.Position the hood on the suction unit (insert it partially), connect the electr...