Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
• Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides. • Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames. • When frying, never leave the pan unattended. • The hood should not be used by children or persons not instructed in its correct use. MAINTENANCE • Switch off and unplug the appliance from the mains supply before carrying out any cleaning or maintenance work. • Clean regularly (see Care and Cleaning section), build up of dirt and grease could cause a fire hazard. 3GB GB 4 INSTALLATION Dimensions Components Ref. Q.ty Product Components 1 1 Hood Body, complete with: Controls, Light, Blower, Filters 2 1 Telescopic Chimney comprising: 2.1 1 Upper Section 2.2 1 Lower Section 9 1 Reducer Flange o 150-120 mm 14.1 2 Air Outlet Connection Extension 15 1 Air Outlet Connection Ref. Q.ty Installation Components 7.2.1 2 Upper Chimney Section Fixing Brackets 11 6 Wall Plugs 12a 6 Screws 4,2 x 44,4 12b 4 Screws 3,5 12e 6 Screws 2,9 x 9,5 Q.ty Documentation 1 Instruction Manual INSTALLATION Wall drilling and bracket fixing Wall marking: • Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of the area in which the hood will be installed. • Draw a horizontal line at 650 mm above the hob. • Place bracket 7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the centre (notch) with the vertical reference line. • Mark the wall at the centres of the holes in the bracket. • Place bracket 7.2.1 on the wall as shown at X mm below the first bracket (X = height of the upper chimney section supplied), aligning the centre (notch) with the vertical line (see diagram above). • Mark the wall at the centres of the holes in the bracket. • Mark a reference point as indicated at 116 mm from the vertical reference line and 323 mm above the horizontal reference line. • Repeat this operation on the other side. • Drill o 8 mm holes at all the centre points marked. • Insert the wall plugs 11 in the holes. • Fix the brackets using the 12a screws (4,2 x 44,4) supplied. • Insert the two screws 12a (4,2 x 44,4) supplied in the hood body fixing holes, leaving a gap of 56 mm between the wall and the head of the screw. Mounting the hood body • Before attaching the hood body, tighten the two screws Vr located on the hood body mounting points. • Hook the hood body onto the screws 12a • Fully tighten support screws 12a • Adjust screws Vr to level the hood body. 5GB GB 6 Upper exhaust flue • Slightly widen the two sides of the upper flue and hook them behind the brackets 7.2.1, making sure that they are well seated. • Secure the sides to the brackets using the 4 screws 12e (2,9 x 9,5) supplied. Lower exhaust flue • Slightly widen the two sides of the flue and hook them between the upper flue and the wall, making sure that they are well seated. • Fix the lower part laterally to the hood body using the 2 screws 12e (2,9 x 9,5) supplied. Connections DUCTED VERSION AIR EXHAUST SYSTEM When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe o 150 or 120 mm, the choice of which is left to the installer. • To install a o 120 mm air exhaust connection, insert the reducer flange 9 on the hood body outlet. • Fix the pipe in position using sufficient pipe clamps (not supplied). • Remove any activated charcoal filters. RECIRCULATION VERSION AIR OUTLET • Push the connection 15 onto the air outlet. • Insert the connection extension pieces laterally 14.1 in connection 15. • Fix the connection extension 14.1 to the connection 15 using the 4 screws 12b (3,5) supplied. • Ensure that the activated charcoal filters have been inserted. Flue assembly 7.2.1 Electrical Connection WARNING: This appliance MUST be earthed. Connect to a 230 - 240V A.C. Supply only. • Connection to the electricity supply should be made via a properly earthed, readily accessible wall socket which is adjacent to and not more than 1.25m away from the appliance and capable of electrical isolation. Should this plug not fit the socket outlet in your home it should be cut off and replaced with a suitable plug as outlined below. Note: The removed plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children might find it and plug it into a supply socket -with the obvious consequent danger. IF THE FITTED PLUG IS REMOVED The flexible mains lead must be correctly connected as below, to a three pin plug of not less than 13 amp capacity. If a B.S.1363 fused plug is used, it must be fitted with a 3amp fuse which is approved to B.S.1362. IMPORTANT: The wires in the mains lead fitted to this appliance are coloured in accordance with the following code: GREEN and YELLOW -EARTH BLUE - NEUTRAL BROWN -LIVE CORD CLAMP 3amp FUSE As the colours of the wires in the mains lead of th...