Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
• For hollow brick ceilings of wall thickness of approximately 20mm: use 4 plugs 11 and 4 screws 12h (5.2 x 70), provided. • For wooden beam ceilings, use 4 wood srews (not provided). • For wooden shelf, use 4 screws 12g (M6 x 80) with washers 22 and nuts 23, provided. Lower Frame • Fix the lower frame using the 8 previously removed screws, adjusting the length according to the installation height (hood body lower fixing surface must be at least 710mm from the hob). • For the recirculation version, turn the frame in the direction chosen for the recirculated air outlet. • The frame mounting must be secure to withstand the weight of the hood and any stresses caused by the occassional side thrust applied to the device. On completion, check that the base is stable, even if the frame is subjected to bending. • In all cases where the ceiling is not strong enough at the suspension point, the installer must provide strengthening, using suitable plates and backing pieces anchored to the structurally sound parts. GB 7 INSTALLATION Connections DUCTED VERSION AIR EXHAUST SYSTEM When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe o 150 or 120 mm, the choice of which is left to the installer. • To install a o 120 mm air exhaust connection, insert the reducer flange 9 on the hood body outlet. • Fix the pipe in position using the pipe clamps 25 provided. • Remove any activated charcoal filters. RECIRCULATION VERSION AIR OUTLET • Push the connection 15 onto the air outlet. • Insert the connection extension pieces laterally 14 in connection 15. • Place the upper chimney section and fix the upper part to the Fixing Part of the Upper Chimney using the 2 screws 12c (2.9 x 9.5) provided. • Similarly, position the lower chimney section and fix the lower part to the frame using the 2 screws 12c (2.9 x 9.5) provided. Recirculation version • Make sure that the outlet of the extension pieces 14.1 is horizontally and vertically aligned with the chimney outlets. • If this is not the case, remove the lower chimney section and adjust the position by either reversing the connection pieces 14.1 or by cutting the hood body extension 14 along one of the thinner section channels denoting the pre-fixed lengths, then reassemble as described previously. • Fit the directional grids 8a-8b in their housings making sure that the directional symbols are towards the top. Also make sure that they are correctly inserted in the connection extension pieces 14.1. GB 8 INSTALLATION Connections Before fixing the hood body to the frame: • Remove the grease filters from the hood body. • Remove any activated charcoal filters. • From below, use the 4 screws 12f (M6 x 10) provided, to fix the hood body to the frame. • Fix the Lower Chimney to the Hood Canopy using the 2 screws 12c (2.9 x 9.5) provided. ELECTRICAL CONNECTIONS WARNING THIS APPLIANCE MUST BE EARTHED This appliance must be connected by a competent person eg. NICEIC registered contractor, in accordance with latest IEE regulations. The appliance is supplied with a fitted plug. If the appliance is to be connected to fixed wiring, it must be connected to a double-pole control unit with a minimum switch rating of 5A and protected by a 3A fuse. • Connect the hood to the mains through a double pole switch having a contact gap of at least 3mm. • Connect the control connector Cmd. • Place the connector in the junction box 24 and close it using the 2 screws 12e (2.9 x 6.5) provided. • Fix the junction box to the hood body using the 2 screws 12c (2.9 x 9.5) provided. • For the recirculation version, fit the activated charcoal filter. • Replace the grease filters. GB 9 Electrical Connection WARNING: This appliance MUST be earthed. Connect to a 230 - 240V A.C. Supply only. • Connection to the electricity supply should be made via a properly earthed, readily accessible wall socket which is adjacent to and not more than 1.25m away from the appliance and capable of electrical isolation. Should this plug not fit the socket outlet in your home it should be cut off and replaced with a suitable plug as outlined below. Note: The removed plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children might find it and plug it into a supply socket - with the obvious consequent danger. IF THE FITTED PLUG IS REMOVED The flexible mains lead must be correctly connected as below, to a three pin plug of not less than 13 amp capacity. If a B.S.1363 fused plug is used, it must be fitted with a 3amp fuse which is approved to B.S.1362. IMPORTANT: The wires in the mains lead fitted to this appliance are coloured in accordance with the following code: GREEN and YELLOW - EARTH BLUE - NEUTRAL BROWN -LIVE CORD CLAMP 3amp FUSE As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:- The wire which is green and yellow must...