Assessments - 5, GPA: 3.8
(
)
)
|
Facilidade de uso
• Reinstall drywall and refinish. IMPORTANT Framing must be capable of supporting 100 lbs. Step 1: • Make sure that no cables or pipes will become damaged (e.g. electric, gas, water; test the areas in question with a cable detector). • Using supplied template (15), mark and drill 8 holes in the wall. Drill the holes according to the measured distances from the diagram (fig. ). • Upper/Lower bracket (3, 4): Insert 4 wall plugs (9) into the 4 drilled holes. • Range hood (1): Installation is depending on wall type: Wall type Required fasteners Wood No wall plugs (9) required Brick/Concrete 4 wall plugs (9) GB 8 GB fig. 2.95” 5.1” 15.67” 0.86” Long screws 1.5” Wood screws 8.3” 5.9” 15.98”-FHWC3055L 23.86”-FHWC3655L Ceiling Wall Dimension A (see table) Desired range hood distance above a 36” high cook top Ceiling height 8 Feet 9 Feet 10 Feet *1 A*2 A*2 A*2 26”*3 27-5/16” 27”*3 28-5/16” 28-5/16” 28”*3 29-5/16” 29-5/16” 29-5/16” 29”*3 30-5/16”*4 30-5/16” 30-5/16” 30”*3 31-5/16”*4 31-5/16” 31-5/16” 31”*3 32-5/16”*4 32-5/16” 32-5/16” 32”*3 33-5/16”*4 33-5/16” 33-5/16” 33” 34-5/16” 34-5/16” 34” 35-5/16” 35-5/16” 35” 36-5/16” 36-5/16” *1: with 10’ xtension chimney kit FHW10X55LS (14) (not supplied). Please call Frigidaire at 1.800.944.9044 to order this kit. *2: “Dimension A” in the chart represents the height from cook top to where the bottom screw mounting holes would be located. *3: Recommended mounting height *4: Recirculation Kit cannot be installed. Step 2: • Install the range hood (1) either with wood screws or long screws, depending on the wall type: Wall type Required screws Wood 4 wood screws (11) Brick/Concrete 4 long screws (8) • Insert 2 screws (8 or 11) in the top location, but do not fully insert the screws (fig. ). Mount the range hood (1) to the wall and tighten the screws. Insert and tighten the 2 remaining screws on the bottom location of the range hood (fig. / ). • Attach the collar (5) to the range hood (1). Secure with 2 short screws (8) (fig. ). 0.08” 0.08” fig. fig. fig. fig. NOTE Sometimes, sponge tape covers the holes. If the holes are located behind the sponge tape, simply insert the screw through the sponge tape. Step 3: • Mount upper and lower brackets (3, 4) on the wall. Secure with the remaining 4 sets of long screws (8). The notches of the lower bracket should be facing up towards the ceiling (fig. ). • Attach the exhaust duct. In the example below a round metal duct furnace pipe has been used. The airtight connection of the exhaust duct should then be improved with a duct tape. This ensures tight fit and that no grease vapors will escape from the duct (fig. ). fig. fig. 9 GB Electrical connections DANGER Danger of electric shock! All fittings must be installed by a competent person in accordance with current wiring regulations and local building regulations. If in doubt, consult a qualified electrician. IMPORTANT Always switch off the electricity supply at the mains during installation, cleaning and maintenance. We recommend...
Este manual também é adequado para os modelos :Fans - FHWC3655LSA (1.59 mb)
Fans - FHWC3055LSA (1.59 mb)
Fans - FHWC3055LSA (1.59 mb)
Fans - FHWC3055LSA (1.59 mb)