Assessments - 2, GPA: 5 ( )

Fabricante : Dacor Arquivo Tamanho: 705.9 kb Arquivo Nome : Língua de Ensino:

Two staggered 45° angles are better than one 90°. • Keep turns as far away from the hood exhaust as possible, with as much space between each bend as possible. • For best performance, use round duct instead of rectangular, especially when elbows are required. • If multiple elbows are used, try to keep a minimum of 24” (61 cm) of straight duct between them. • Avoid “S” or “back to back” configurations of adjacent elbows. • In regions where the weather gets extremely cold, thermal breaks, such as a short section of non-metallic duct, should be used to avoid indoor heat loss. The break should be located as close to the pass through point to the outside as possible. • Do not use flexible metal duct. • Do not use duct work that is smaller in cross-sectional area than the recommended size duct (8” round). insTallaTion insTruCTions WARNING • Do not install the range hood unless the electrical service provided meets the range hood specifications. • Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. • Aqualifiedtechnicianmustcompletetheinstallation of this built-in appliance. The owner is responsible to make sure the hood is properly installed. • To avoid an electric shock hazard and property damage, locate electric wires and water pipes and avoid drilling in the vicinity. • The range hood is heavy. To prevent personal injury and property damage install the hood only as specified below. Make sure all screws used to mount and assemble the hood are tight. electric SerVice inStallation The electrical connection box must be: • Connected to a 120 Vac, 60 Hz dedicated, grounded, circuit protected by a 15Amp circuit breaker or time delay fuse. • Located a minimum of 17” (43.2 cm) above the bottom of the range hood. mountinG Bracket inStallation 1. Locate the mounting bracket and position it against the ceiling at the previously determined mounting location (see page 5). 2. Using a pencil, mark the four mounting hole locations on the ceiling. 3. Drill four 1/16” (1.6 mm) pilot holes at the mounting hole locations. 4. Attach the bracket using four #12 screws (not supplied). Make sure the screws penetrate into the wood mounting surfaces 1 1/2” (3.8 cm). aSSemBle the hooD WARNING • Lifting and hanging the range hood requires two people. Do not attempt to lift the hood without assistance. 1. Place the hood assembly on a soft surface with the bottom side down during assembly to avoid damage. 2. Tip the hood up on it’s side and remove the filter(s) to reduce weight and avoid damage. 3. Inside the exhaust outlet(s) there are metal or plastic damper flaps. The flaps close to help prevent back- drafts when the blower is turned off. Make sure all the flaps open and close freely before proceeding. Remove any shipping tape that may be present. 4. Remove the tape that holds the wiring in place on top of the hood during shipment. 5. On models with two blowers: Put the exhaust cowling over the blower outlets on the top of the hood. Fasten the cowling in place with 14 machine screws. insTallaTion insTruCTions insTallaTion insTruCTions hooD aSSemBly (cont) 6. Separate the bottom framework piece from the top 9. Attach the hood junction box to the rim of the bottom framework piece. The top frame work piece has 5-inch framework piece using two machine screws as shown. slots on the the sides. The bottom piece has a series of holes on the sides. 7. Position the bottom framework piece on top of the hood. Slide the studs on the top of the hood into the holes on the bottom of the framework piece. The cutouts for the wiring allow the bottom framework piece to fit on only one way. If it does not fit properly, turn it 180° so that the cut-outs line up. Make sure all wiring is tucked inside the framework piece and are not pinched. FRAMEWORK BOTTOM HOOD 8. Useeightprovidedlockwashersandnutstosecurethebottomframeworkpiecetothetopofthehood. HOOD JUNCTION BOX EXTERNAL MOTOR TERMINAL BLOCK 10. Attach the external motor terminal block to the rim of the bottom framework piece using two machine screws as shown. It mounts on the opposite side of the hood junction box. insTallaTion insTruCTions insTallaTion insTruCTions 11. Determine the required framework height. To determine the required framework height: • Measure the distance from the ceiling to the cooktop. • Subtract the height at which the hood will be mounted (30” minimum) and the hood thickness (12 1/2”) from the distance measured. 12. Put the top framework piece over the bottom framework piece. The mounting slots on the top piece must be up. 13. Use four machine screws to fasten the top piece to the bottom piece. The total height of the two pieces together must equal the required framework height determined above. 14. Remove the protective plastic covering from both pieces of the chimney assembly. Do not remove the protective tape strips from the inside. They protect the telescoping pieces from scratching during i...

Baixe o seu

Para fazer o download, introduza 2 dígitos :