Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
. The backsplash filters height will determine the position of the bottom edge of the range hood canopy. Page 3 Attachment l/8" brackettop ; ; ; to ceiling 1 I I I I I I I I middle I I : bracket +z& I ’ I I I I I I I I I I 34-518” min. I 24” min. 3. The range hood chimney adjusts to meet varying ceiling heights from 8 feet to 9 feet. Determine and Electrical connection Electrical Shock Hazard l Electrical ground is required on this appliance. 9 Do Not connect to the electrical supply until the appliance is permanently grounded. l Disconnect power to the junction box before making the electrical connection. l This appliance must be connected to a grounded, metallic, permanent wiring system, or a grounding connector should be connected to the grounding terminal or wire lead on the appliance. Failure to do so could result in a fire, personal injury or electrical shock. Install chimney sections 12 Attach damper to exhaust opening on n top of canopy using two Phillips-head screws. Connect ductwork to damper and seal all connections with duct tape. Check operation 15 n Turn power on. I -.. _ Check the operation of the range hood: -5zaiz~>~>17n control panel = =--.- location The range hood controls are located in a n grey panel on the underside of the canopy. To open the panel, press up on front edge of panel and release. The control panel will drop down. Page 4 mark the location of the chimney mounting brackets: l Top bracket: l/8’ from the ceiling. l Bottom bracket: IO-5/8’ above bottom edge of range hood canopy. l Middle bracket: At the bottom edge of the upper chimney sleeve. Note: If canopy is mounted more than 24 inches above countertop, it may be necessary to cut the upper chimney sleeve. Use great care not to damage or bend upper chimney sleeve when cutting. 4 Install the top and middle brackets with ends n touching wall and curves facing out. Install bottom bracket with metal flanges on the bottom. Check that brackets are securely fastened to wall. 5 5 Determine and make all necessary cuts in n wall or ceiling for ductwork. Install ductwork. (See “Venting requirements” section, Page 2.) 6 6 Disconnect power supply. Run wiring n through wall or cabinets according to National Electrical Code and local codes and ordinances. Do Not turn on power until installation is completed. AI / w Press on handle in front of filters to release filters from range hood canopy. Remove filters and set aside. 8 8 Remove the terminal box cover from the n range hood. Remove the power supply cable knockout using a flat-blade screwdriver. 11n Make electrical connection: q Connect the power supply cable to range hood terminal box through the U.L.-listed conduit connector. l7J Connect the white wire of the power supply cable with the white lead in the range hood, using a twist-on connector; connect the black wire of the power supply cable with the black lead in the range hood, using a twist-on connector. 0 Connect the power supply green (green and yellow) grounding wire under the green, grounding screw. l7J Tighten conduit connector screws. i7J Replace the terminal box cover. 13 13 Position upper chimney on top and middle n brackets. Slide lower chimney over upper chimney. Slide lower chimney down onto lower bracket and canopy for a snug fit. Then secure chimney pieces to brackets with screws provided. I I “IQ I-la@ -l-o I c 3: 0 1 QO1 --mm1 light switch blower switch blower speed switch q Move light switch to “1” position. The light should turn on. q Move the blower switch to “1” position. The blower should operate. q Move the blower speed switch to the far left; blower speed should be LOW. Move blower speed to right, blower speed should gradually increase until you reach HIGH speed at far right. Personal Injury Hazard Because of the weight and size of the range hood canopy, two or more people are needed to move and safely install the range hood canopy. Failure to properly lift range hood could result in damage to the product or personal injury. 9 9 Rotate the two adjustment screws halfway n into slots. Hang canopy from flange of lower bracket, making sure that tabs are fully inserted in slots and canopy is secure on bracket. Adjust the height of the canopy by rotating the two screws. Attach conduit connector to power supply cable opening so that conduit connector clamping screws are on inside of range hood. Feed enough power supply cable through conduit connector to make electrical connections. 10 10 Check that canopy is level. If needed, n turn adjusting screws until canopy is level. 14 14 Place filters in canopy opening so rear n edge is over flange. Press filters up into position. q Move blower and light switches to “0” position to turn blower and light off. If range hood does not operate: q Check that the circuit breaker is not tripped or the house fuse blown. To get the most efficient use from your new range hood, read the “Use and Care Information” section. Keep your KitchenAid Installation Instructions and Use and Care Guid...
Este manual também é adequado para os modelos :Fans - 6899551 (785.76 kb)