Assessments - 3, GPA: 3.7 ( )

Fabricante : KitchenAid Arquivo Tamanho: 507.91 kb Arquivo Nome : Língua de Ensino:

¦ Do not terminate the vent system in an attic or other enclosed area. ¦ Do not use 4" (10.2 cm) laundry-type wall caps. ¦ Use metal vent only. Rigid metal vent is recommended. Plastic or metal foil vent is not recommended. ¦ The length of vent system and number of elbows should be kept to a minimum to provide efficient performance. For the most efficient and quiet operation: ¦ Use no more than three 90° elbows. ¦ Make sure there is a minimum of 24" (61.0 cm) of straight vent between the elbows if more than 1 elbow is used. ¦ Do not install 2 elbows together. ¦ Use clamps to seal all joints in the vent system. ¦ The vent system must have a damper. If the roof or wall cap has a damper, do not use the damper supplied with the grill vent hood. ¦ Use caulking to seal exterior wall or roof opening around the cap. ¦ The size of the vent should be uniform. Venting Methods This canopy grill vent hood is factory set for venting through the roof or through the wall. A 10" (25.4 cm) round vent system is needed for installation (not included). The hood exhaust opening is 10" (25.4 cm) round. NOTE: Flexible vent is not recommended. Flexible vent creates back pressure and air turbulence that greatly reduce performance. Vent system can terminate either through the roof or through the wall. To vent through a wall, a 90° elbow is needed. Rear discharge A 90° elbow may be installed immediately above the hood. Roof Venting Wall Venting A A B B C C D D A. Optional decorative duct cover A. Optional decorative duct cover B. 10" (25.4 cm) round vent B. 10" (25.4 cm) round vent and elbow C. Roof cap C. Wall cap transition D. 10" (25.4 cm) round vent transition D. 10" (25.4 cm) round vent Calculating Vent System Length To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system. Vent Piece 10" (25.4 cm) Round 45° elbow 2.5 ft (0.8 m) 90° elbow 5.0 ft (1.5 m) Maximum equivalent vent length is 35 ft (10.7 m). Example vent system Wall cap 6 ft (1.8 m) 90 elbow 2 ft (0.6 m) The following example falls within the maximum recommended vent length of 35 ft (10.7 m). 1 - 90° elbow = 5.0 ft (1.5 m) 1 - wall cap = 0.0 ft (0.0 m) 8 ft (2.4 m) straight = 8.0 ft (2.4 m) Length of system = 13.0 ft (3.9 m) Electrical Requirements Observe all governing codes and ordinances. Ensure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances. If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. A copy of the above code standards can be obtained from: National Fire Protection Association One Batterymarch Park Quincy, MA 02269 CSA International 8501 East Pleasant Valley Road Cleveland, OH 44131-5575 ¦ A 120 Volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required. ¦ If the house has aluminum wiring follow the procedure below: 1. Connect a section of solid copper wire to the pigtail leads. 2. Connect the aluminum wiring to the added section of copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum. Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices. ¦ Wire sizes and connections must conform with the rating of the appliance as specified on the model/serial rating plate. The model/serial plate is located behind the filter on the rear wall of the hood. ¦ Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances. INSTALLATION INSTRUCTIONS Prepare Location ¦ It is recommended that the vent system be installed before hood is installed. ¦ Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust vent. ¦ Check your ceiling height and the hood height maximum before you select your hood. 1. Disconnect power. 2. Determine which venting method to use: roof or wall. 3. Select a flat surface for assembling the grill vent hood. Place covering over that surface. WARNING Excessive Weight Hazard Use two or more people to move and install grill vent hood. Failure to do so can result in back or other injury. 4. Using 2 or more people, lift grill vent hood onto covered surface. Tip the hood on its back and remove filters and set aside. To Remove Filters: 1. Using the filter handles, pull filter towards the front of the grill vent hood. B C A A. Filter handles B. Front edge of filter C. Back edge of filter Step 1 Step 2 Step 3 2. Pivot the back edge of the filter towards the back of the grill vent hood. 3. Drop the front edge of the filter dow...

Baixe o seu

Para fazer o download, introduza 2 dígitos :