Assessments - , GPA: ( )

Instruções de Operação Emerson, Modelo CF1PW01

Fabricante : Emerson
Arquivo Tamanho: 330.43 kb
Arquivo Nome :

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

6 NOTE: CEILING COVER, SUPPLY WIRES AND OUTLET FAN WIRES OMITTED BOX FOR CLARITY. HANGER BRACKET Figure 14 DOWNROD ASSEMBLY HANGER BALL/ WARNING ! To avoid possible fire or shock, do not pinch wires between the hanger ball/downrod assembly and the hanger bracket. How to Wire Your Ceiling Fan If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. 1. Connect the green grounding lead from the hanger ball and the green grounding lead from the hanger bracket to the grounding conductor of supply (this may be a bare wire or wire with green colored insulation) (Figure 15). Securely connect wires with wire connector supplied. WARNING ! To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. NOTE: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it must be grounded for safe operation. BLACK AND BLUE SUPPLY GROUND WIRE LISTED WIRE GREEN WIRE NOTE: CEILING COVER OMITTED FOR CLARITY. CONNECTOR (3) (GROUND) FROMHANGER BRACKET GREEN WIRE (GROUND) FROMHANGER BALL WHITE SUPPLY (NEUTRAL) WHITE FAN WIRE BLACK SUPPLY (HOT) FAN WIRES 2. Securely connect the fan motor white wire to the supply white (neutral) wire using wire connector supplied (Figure 15). Securely connect the fan motor black wire and blue wire to the supply black (hot) wire using wire connector supplied (Figure 16). After connections have been made, turn leads upward and carefully push leads into the outlet box, with the white and green leads on one side of the outlet box and the black and blue leads on the other side of the outlet box. WARNING ! Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until blades are in place. Noise and fan damage could result. 3. Screw the two 1-1/4” threaded studs (supplied) into the tapped holes in the hanger bracket (Figure 16). 4. Lift the ceiling cover and the ceiling cover trim up to the threaded studs and turn until studs protrude through the holes in the ceiling cover and trim (Figure 16). 5. Secure the ceiling cover and trim in place by sliding lockwashers (supplied) over the threaded studs and installing the two knurled knobs (supplied) (Figure 16). Tighten the knurled knobs securely until the ceiling cover fits snugly against the ceiling and the hole in the ceiling cover is clear of the downrod. Your fan is now wired to be turned on and off from the fan switch. 1-1/4" THREADED CEILING STUD COVER LOCKWASHER CEILINGCOVERTRIM KNURLED KNOB Figure 16 WARNING ! To avoid possible fire or shock, make sure that the electrical wires are completely inside the outlet box and not pinched between the ceiling cover and the ceiling. Figure 15 NOTE: If you are using an Emerson Light Fixture with your fan, see Light Fixture Owner’s Manual for wiring. 7 Using Your Ceiling Fan Attaching Light Kit 1. Restore electrical power to the outlet box by To install an accessory light kit, first unscrew the finial turning the electricity on at the main fuse box. and remove the lower trim (Figure 18). Then remove the center trim by removing four 8-32 x 1/2” screws. 2. Check the operation of the fan by gently pulling on Remove the threaded nipple from the center trim and the 4-position speed control pull chain switch install the light kit in accordance with the light kit (Figure 17). The operating sequence is as follows: Owner’s Manual. REVERSING SWITCH SPEED CONTROL PULL CHAIN SWITCHTHREE-SPEED 1st Pull—HIGH WARNING ! To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. SPEED CONTROL PULL CHAIN SWITCH THREADED NIPPLE LOWER TRIM FINIAL 8-32 x 3/8" SCREW (4) CENTER TRIM 2nd Pull—Medium 3rd Pull—Low 4th Pull—OFF Figure 18 Figure 17 3. If airflow is desired in opposite direction, turn your fan off and wait for the blades to stop turning, then press the rocker switch located on top of the motor housing, and turn the fan on again. The fan blades will turn in the opposite direction and reverse airflow. 8 Maintenance IMPORTANT CARE INSTRUCTIONS for your Ceiling Fan Periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning, use only a soft brush or lint free cloth to avoid scratching the finish. Abrasive cleaning agents are not required and should be avoided to prevent damage to finish. WARNING ! Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock. Accessories 1. Ceiling Fan Light Kits (see store or catalog). 2. Downrod Extension Kits (see store or catalog). 3. Ceiling Fan Controls (see store or catalog). WARNING ! WARNING ! The use of any other control not specifically approved for this fan could result in fire, shock and personal injury. This product is designed to use only those parts supplied wi...