Assessments - 4, GPA: 4.3 ( )

Fabricante : Emerson Arquivo Tamanho: 203.29 kb Arquivo Nome : Língua de Ensino:

half of styrofoam unit. Remove parts and check to see that you have received the following: a. Fan motor and housing assembly b. One motor cover c. One ceiling cover d. Five blade flanges e. One hanger ball/downrod assembly f. One hanger bracket g. One housing switch cup h. One loose parts bag containing: 1. One setscrew 2. One 3/16" hex wrench 3. Eleven 10-32 x 5/8" oval head screws 4. Two 1” threaded studs 5. Two 1-1/4” threaded studs 6. Four knurled knobs 7. Three wire connectors 8. Four 8-32 x 5/16” flat head screws 9. One pull chain pendant 10. One pull chain coupling 11. One hairpin clip 12. One clevis pin 13. Four lockwashers CEILING COVER FOAM PACKING PROTECTIVE PLASTIC BAG FOAM PACKING CARTON MOTOR AND HOUSING ASSEMBLY HANGER BALL/ DOWNROD ASSEMBLY HANGER BRACKET LOOSE PARTS BAG BLADE FLANGES MOTOR COVER HOUSING SWITCH CUP 14. Sixteen 10-32 x 3/8" pan head screws 15. Sixteen flat washers 4 Assembly Instructions 1. Remove the fan motor and housing assembly from styrofoam packaging and position it so that the top of the motor is facing you. 2. Separate, untwist and unkink the three motor leads. Route the motor leads through the hanger ball/downrod assembly and seat the downrod in the motor coupling. 3. Align the clevis pin holes in the downrod with the holes in the motor coupling. Install the clevis pin and secure with the hairpin clip. The clevis pin must go through the holes in the motor coupling and the holes in the downrod. Push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin. The hairpin clip must be properly installed to prevent the clevis pin from working loose. Pull on the hanger ball to make sure the clevis pin is properly installed. WARNING ! It is critical that the clevis pin in the motor coupling is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed could result in the fan falling. 4. Install the setscrew (supplied in loose parts bag) in the motor coupling. While pulling up on the hanger ball, tighten the setscrew using the 5/32" setscrew wrench (supplied). NOTE: The setscrew must be properly installed as described above, or fan wobble could result. SETSCREW WRENCHDOWNROD MOTOR COUPLING SETSCREW CLEVIS PIN MOTOR COUPLING HANGER BALL DOWNROD HAIRPIN CLIP HAIRPIN CLIP CLEVIS PIN HANGER BALL/ DOWNROD ASSEMBLY CLEVIS PIN 5 5.Remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod. Remove the pin from the downrod, then remove the hanger ball. Retain the pin and hanger ball for reinstallation in step 8. HANGER BALL DOWNROD PIN SETSCREW 6.Screw two 1” threaded studs (provided) into the motor. Leave approximately 7/8” of the stud extending above motor. Slide the motor cover over the downrod and rotate the cover until the threaded studs protrude; install two knurled knobs (supplied) to secure the cover. NOTE: Make sure the red and brown leads are capped with wire connectors and are completely inside motor cover and not pinched between the motor cover and motor. 1" THREADED STUD MOTOR COVER KNURLED KNOB MOTOR 7/8" RED LEAD BROWN LEAD WIRE CONNECTORS 7.Position the ceiling cover over the downrod. Be sure the cover is oriented correctly, with the large opening at the top. 8.Reinstall the hanger ball on the downrod as follows. Route the motor leads through the hanger ball and slide the hanger ball over the downrod. Install the pin through the holes at the top of the downrod and slide the hanger ball up the downrod, aligning the ball so the pin is captured in the groove in the top of the hanger ball. Pull the hanger ball up tight against the pin and securely tighten the setscrew in the hanger ball. A loose setscrew could create fan wobble. WARNING ! It is critical that the pin in the hanger ball is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed could result in the fan falling. SETSCREW DOWNROD PIN HANGER BALL CEILING COVER 6 9. The fan comes with blue, black and white leads that are 80-inches long. Before installing fan, measure up approximately 6 to 9-inches above the ball/downrod assembly. Cut off excess leads and strip back insulation 1/2-inch from end of leads. 10. Use three 10-32 x 3/8" pan head screws and flat washers (supplied) to secure flange to blade, as shown below. Repeat for the remaining four blades. 11. Use the 10 round recessed holes in the motor hub marked with "5" and install the five blade assemblies (ordered separately) in accordance with Step 12. 12. Attach one blade assembly...

Baixe o seu

Para fazer o download, introduza 2 dígitos :