Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
Never use gasoline, naphtha, paint thinners, alcohol, or other highly flammable fuels. Do not use heavy fuels such as No. 2 fuel oil or No. 2 Diesel. Using heavy fuels will result in: • clogged fuel filter and nozzle • carbon build up on spark plug • the need of non-toxic anti-icer in fuel during very cold weather IMPORTANT:Use a KEROSENE ONLY storage container. Be sure storage container is clean. Foreign matter such as rust, dirt, or water will cause the flame- out control to shut down heater. Foreign matter may also require you to clean fuel system often. 6 099176 VENTILATION OPERATION WARNING ! Follow the minimum fresh, outside air ventilation requirements. If proper fresh, outside air ventilation is not provided, carbon monoxide poisoning can occur. Provide proper fresh, outside air ventilation before running heater. Provide at least a three-square-foot opening of fresh, outside air for each 100,000 BTU/Hr rating. Provide extra fresh air if more heaters are being used. Example: A 150,000 BTU/Hr heater requires one of the following: • a two-car garage door raised six inches • a single-car garage door raised nine inches • two, thirty-inch windows raised twelve inches ! WARNING Review and understand the warnings in the Safety Information Section, pages 2 and 3. They are needed to safely operate this heater. Follow all local codes when using this heater. To Start Heater 1. Follow all ventilation and safety information. 2. Fill fuel tank with kerosene or No. 1 fuel oil. 3. Attach fuel cap. 4. Plug power cord of heater into three-prong, grounded extension cord. Extension cord must be at least six feet long. Extension Cord Wire Size Requirements 6 to 10 feet long, use 18 AWG rated cord 11 to 100 feet long, use 16 AWG rated cord 101 to 200 feet long, use 14 AWG rated cord 5. Plug extension cord into standard 120 volt/60 hertz, three-hole, grounded outlet. Heater will start when extension cord is plugged into outlet. If not, push in flame-out control reset button (see Figures 5 and 6). Flame- Out Control Reset Button Figure 5 - Flame-Out Control Reset Button, 35/50/55/70,000 BTU/Hr Models Continued Flame- Out Control Reset Button Figure 6 - Flame-Out Control Reset Button, 100/110/150,000 BTU/Hr Models 7 OPERATION Continued STORAGE PREVENTATIVE MAINTENANCE SCHEDULE To Stop Heater 1. Unplug extension cord from outlet. To Restart Heater 1. Wait two minutes after stopping heater. 2. Repeat steps under To Start Heater, page 7. 1. Drain fuel tank. Note: Some models have drain plug on underside of fuel tank. If so, remove drain plug to drain all fuel. If heater does not have drain plug, drain fuel through fuel cap opening. Be sure all fuel is removed. 2. Replace drain plug if used. 3. Add one gallon of clean kerosene to fuel tank. 4. Attach fuel cap. 5. Move heater forwards and backwards to stir fuel. 6. Remove fuel cap or drain plug and drain fuel tank. Be sure all fuel is removed. 7. Replace fuel cap or drain plug. Properly dispose of old and dirty fuel. 8. Store heater in dry place. Make sure storage place is free of dust and corrosive fumes. IMPORTANT: Do not store kerosene over summer months for use during next heating season. Using old fuel could damage heater. ! WARNING Never service heater while it is plugged in, operating, or hot. Severe burns and electrical shock can occur. Item Fuel tank How Often Flush every 150-200 hours of operation or as needed. ...
Este manual também é adequado para os modelos :Fans - 100 (277.27 kb)
Fans - 000 50 (277.27 kb)
Fans - 000 55 (277.27 kb)
Fans - 000 70 (277.27 kb)