Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
16. To prevent overload and blown fuses, be sure that no other appliance is plugged into the same outlet or into another outlet wired into the same circuit. 17. It is normal for the heater’s plug and cord to feel warm to the touch. A plug or cord which becomes hot to the touch or becomes distorted in shape may be the result of a worn electrical outlet. Worn outlets should be replaced prior to further use of the heater. Plugging heater into a worn outlet may result in overheating of the power cord or fire. 18. This heater is not intended for use with an extension cord. Plug the cord directly into an appropriate wall outlet. 19. Be sure that the plug is fully inserted into an appropriate outlet. Please remember that outlets also deteriorate due to aging and continuous use: check periodically if signs of overheating or deformations are present on the plug. If the oulet is deteriorated or damaged, do not use it and CALL your electrician. 20. Check that neither the appliance nor the power cable have been damaged in any way during transportation. 21. Make sure that no pieces of polystyrene or other packaging material have been left between one element of the appliance and another. 22. When switching on the appliance for the first time, allow it to run at full power for at least two hours to get rid of the unpleasant smell. Make sure that the room in which the appliance is located is well ventilated during this operation. It is normal for the appliance to emit small crackling sounds when you turn it on for the first time. 23. CAUTION: to prevent electric shock match wide blade of plug to wide slot, then fully insert. 24. Do not cover the appliance while it is functioning in order to avoid overheating and the risk of fire. SAVE THESE INSTRUCTIONS HOW TO USE BE CAREFUL Operate the heater in upright position only. Any other position could create hazardous situations! ON/OFF Switches POWER ECONOMIZER For more economical use, the Min. or Med. power switches may be used individually, after unit has reached the operating temperature. 700 500 WATTS WATTS With pilot lights ON, the heater is ON! 1. LOCATION Place the heater on the floor beneath the coldest window in the room or any desired location. Your heater will minimize the effect of cold drafts. The heater must not be located immediately below an outlet. Do not use this heater in rooms having a surface area less than 45 sq. ft (4 m2). 2. CONNECTION The radiator must be connected to a properly polarized A/C 110/120 V household outlet in perfect working conditions. Keep loose clothing or bedding, furniture and flammable material away from the wall outlet where the heater plug is fitted in. 3. GROUND FAULT INTERRUPTION SAFETY DEVICE (GFI PLUG) This device provides protection against electric shock due to ground fault currents by automatically shutting off the power. To test the operation of the GFI plug switch the heater ON at either the 1 or 2 setting. Press the TEST button on the GFI plug device attached to the plug end of the power cord. The heater and fan should stop operating and the Power Light should turn off. Press the RESET button on the GFI plug device to resume normal operation of the heater. This device should not be used as on ON/OFF operation switch. “CAUTION: ALTHOUGH THIS DEVICE IS PROVIDED WITH PROTECTION WHICH REDUCES THE RISK OF ELECTRIC SHOCK, THIS PRODUCT SHOULD NEVER BE USED CARELESSLY NEAR WATER.” INSTRUCTIONS FOR USE 4. USE OF THERMOSTAT Turn thermostat clockwise to the maximum position. Switch on both switches. The lights on the switches remain on independently from of the cycling of the thermostat. When the room reaches the desired temperature, turn the thermostat knob clockwise very slowly and carefully until you hear a “click”. This will automatically set your unit to cycle on and off at that desired heat setting. (For timer instructions, see point 5). Note: It will normally require approx.15 minutes to reach operating temperature. Frost prevention mode (anti-freeze setting) Turn the thermostat dial to the position and press the switches. The appliance will maintain a minimum room temperature of approximately 5°C (41 F) thus preventing freezing conditions with a minimum energy consumption. REMINDER To completely shut unit off, ON/OFF switches must be in OFF position. 5.HOW TO USE THE 24 PROGRAMMABLE CLOCK TIMER Please refer to the illustration below: Triangular pointer Tab 2 22 3 33 4 44 5 55 6 66 7 77 1 11 1 11 2 22 0 00 2121 2 22 2 22 2 22 3 33 2424 8 88 9 99 1010 1 11 1 11 1 11 2 22 1 11 3 33 14141 11 5 55 1 11 6 66 1 11 7 77 1818 9 99 Operating IMPORTANT: There are 96 notches around the dial. Each notch represents a 1/4 hour (15 minutes). Your appliance can be programmed to switch itself ON and OFF at the time you want. With the timer you can approximate your settings to within 15 minutes and program up to 48 cycles (1 cycle = 1 “ON” + 1 “OFF”) over a period of 24 hours (12 hours a.m.+12 hours p.m.). The notches can be pushed inwards or pu...