Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
9. This product is equipped with a thermostat which may start blower automatically. To reduce the risk of injury and to prevent power from being switched on accidentally, switch power off at service panel and lock or tag service panel. 10. Please read specification label on product for further information and requirements. - 4 PREPARE THE HOOD Unpack hood and check contents. You should receive: 1 - Hood 1 - Decorative Flue Assembly 1 - Parts Bag (B080810480) containing: 1 - Mounting Bracket 1 - Discharge Collar 1 - Flue Mounting Bracket 8 - Mounting Screws (4,8 x 38mm Pan Head) 2 - Mounting Screws (3,9 x 9,5mm Pan Head) 2 - Mounting Screws (3.9 x 6mm Flat Head) 8 - Drywall Anchors 1 - Installation Instructions 1 - Warranty Card DECORATIVE FLUE MOUNTING BRACKET 2 MOUNTING SCREWS (3,9 x 9,5mm Pan Head) 2 MOUNTING SCREWS (3.9 x 6mm Flat Head) DISCHARGE COLLAR FLUE MOUNTING 8 MOUNTING SCREWS 8 DRYWALL ANCHORS BRACKET (4,8 x 38mm Pan Head) - 5 INSTALL THE DUCTWORK (DUCTED HOODS ONLY) NOTE: To reduce the risk of fire, use only metal ductwork. 1. Decide where the ductwork will run between the hood and the outside. 2. A straight, short duct run will allow the hood to perform most efficiently. 3. Long duct runs, elbows, and transitions will reduce the performance of the hood. Use as few of them as possible. Larger ducting may be required for best performance with longer duct runs. 4. Install a roof or wall cap. Connect round metal ductwork to cap and work back towards hood location. Use duct tape to seal the joints between ductwork sections. WIRING Note: This range hood must be properly grounded. The unit should be installed by a qualified electrician in accordance with all applicable national and local electrical codes. GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded. ROOF CAP ROUND DUCT DECORATIVE FLUE HOOD WALL CAP ROUND ELBOW 24” TO 30” ABOVE COOKING SURFACE 6” ADAPTER WARNING - Improper grounding can result in a risk of electric shock. Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded. Do not use an extension cord. If the power supply cord is too short, have a qualified electrician install an outlet near the appliance. Set the electrical power supply within the space covered by the decorative flues. Position the power socket at a maximum distance of 33-7/16” (85 cm) from where the lead exits from the hood (see illustration alongside). Make sure this does not inter fere with the bracket fastening area or with the decorative flue (where the flue touches the wall). Fit the plug into the power socket. - 6 INSTALL MOUNTING FRAMING BEHIND DRYWALL BRACKET 1. Construct wood wall framing that is flush with interior surface of wall studs. Make sure: a) the framing is centered over installation location. b) the height of the framing will allow the mounting bracket to be secured to the framing within the dimensions shown. 2. After wall surface is finished, secure mounting bracket to framing using dimensions shown. 37-7/8” to 43-7/8” abovecooktop 37-7/8"= bottom of hood 24" above cooktop 43-7/8"= bottom of hood 30" above cooktop INSTALL FLUE MOUNTING BRACKET DUCTED AND NON-DUCTED 1. Assemble the flue mounting bracket, adjusting outside width as shown. Fig.4 2. Carefully center the mounting bracket directly over the range hood location. 3. Secure the bracket assembly to the ceiling using (2) 4.8x38mm mounting screws and drywall anchors. Make sure the bracket is pushed into the corner, tight against the wall and centered over the hood. FLUE MOUNTING BRACKET 7-3/4” (196.8mm) FIG. 4 3.9 x 6mm FLAT HEAD BRACKET SCREWS - 7 - 8 - DISCHARGE COLLAR UPPER FLUE LOWER FLUE UPPER FLUE VENTS EXPOSED UPPER FLUE VENTS CONCEALED FIG. 6 FIG. 5 6” DIAMETER DUCT PREPARE THE HOOD Note: On stainless steel hoods, carefully remove the plastic protective film from all exterior surfaces of the hood and decorative flues, prior to final installation. DUCTED CONFIGURATION 1. Install the discharge collar into the duct connector of the range hood. Fig. 5 2. Attach an adequate length of 6” round steel ducting to the range hood duct connector. Fig. 5 3. Duct tape all joints to make them secure and air tight. 4. Carefully place the lower decorative flue into the recessed area of the range hood top. Fig. 6. 5. Carefully slide the upper decorative flue down inside the lower flue. Fig. 6. Note: On 8” ceilings the air vents on the upper flue are concealed by installing the flue with air vents down. On 9” ceilings, air vents on the upper flue will be exposed after installation. DUCT CONNECTOR PREPARE THE HOOD NON - DUCTED CONFIGURATION Note:...