Assessments - 3, GPA: 5
(
)
)
|
Facilidade de uso
6. Rear Right Speaker Out Pin: Connect the RET-R connector to this pin. 7. Rear Left Speaker Out Pin: Connect RET-L connector to this pin. 3.5” Device Installation With the front bezel facing you, swing the front door open. It can swing 270 degrees so the door will be parallel with the side of the case. You can see there are four 5.25” and one 3.5” external drive bays. Inside the case there are two 3.5” drive cages, which can house up to six hard drives. Note: we recommend using the lower HDD cage for your hard drives to maximize the cooling and Quiet Computing™ potential of the case. Upper HDD Installation Note: If you install any HDD’s in this location you will NOT be able to use the Middle Fan as described in the Cooling System section of the manual. 1. Remove the thumbscrew holding the upper HDD cage. 2. Pull the HDD cage from its position by pulling the ring. Note: If you want to install the optional front 120mm fan, you should do so before continuing. Please refer to the Cooling System section for further details. 3 3. There are two HDD trays inside the cage. Squeeze the metal clips on each side of a tray and slide it out. 4. Mount your hard drive to the drive tray with the special screws provided. Don’t over-tighten the screws since that could decrease the grommets’ ability to absorb vibration and noise. Note: Always mount the hard drive with the thicker side of the silicone grommets contacting the hard drive. 5. Slide and lock the tray back into the case. 6. Repeat this if you want to mount another hard drive in the upper cage. 7. Slide the cage back to the case and fasten the thumbscrew. 8. Please refer to the power supply installation section to route the power cables to your devices. Once you’ve done so, connect the appropriate power connectors to your device. The Lower HDD Installation. 1. Remove the thumbscrew holding the lower HDD cage. 2. Pull the HDD cage from its position by pulling the ring. 3. You can mount four hard drives inside the cage. They are mounted vertically with silicone grommets on both sides. 4. Mount your hard drive into the drive cage with the special screws provided. (These screws are in the toolbox attached to the back of the upper HDD cage.) Don’t over-tighten the screws since that could decrease the grommets’ ability to absorb vibration and noise. Note: Always mount the HDD with the thicker side of the silicone grommets facing up. 5. Repeat the same procedure for the other drives as necessary. 6. Slide the cage back into the case and fasten the thumbscrew. 7. Please refer to the power supply installation section, to route the power cables to your devices. Once you’ve done so, connect the appropriate power connectors to your device. External 3.5” Drive Installation There is one external 3.5” drive bay. 1. Carefully remove the plastic drive bay cover and metal plate covering the drive bay. 2. Find the pair of 3.5” drive rails from the box that also contains the top fan spoiler. 3. Mount the drive rails onto the sides of the 3.5” device. Make sure the metal portion is facing forward and angled outward. 4. Slide the device into the drive bay until you hear it click into place. 5. Please refer to the power supply installation section, to route the power cables to your devices. 6. Connect a small 4-pin connector from the power supply to the male 4-pin connector on the floppy drive. 5.25” Device Installation There are four 5.25” drive bays in the P180B. 1. Carefully remove the plastic drive bay cover and the metal plate covering the drive bay. 2. Mount the drive rails onto the sides of the 5.25” device. Make sure the metal portion is facing forward and angled outward. 3. Slide the device into the drive bay until you hear it click into place. 4. Mount the other devices accordingly. 4 5. Please refer to the power supply installation section, to route the power cables to your devices. Once you’ve done so, connect the appropriate power connectors to your device. Installing the power supply 1. With the case upright and both side panels removed (see Setting Up), remove the screws on both sides of the power supply retaining cage and pull the cage out. 2. Slide your power supply into the cage, and slide the cage with power supply back into the case. Note: You can mount the power supply either side up, but don’t fasten the power supply and cage to the case at this time. 3. There is a plastic sliding panel assembly between the upper and lower chambers that lets you run power and data cables between the chambers while maintaining thermal isolation. It has two parts, one large and one small, both of which can slide independently to adjust the size of the openings. Loosen the two thumbscrews holding the panels and slide the large panel all the way to the rear of the case to fully expand the opening. 4. Carefully guide all the power cables through the opening to the upper chamber. Route power cables to your installed upper chamber devices and make the appropriate connections. Note: you may ...
Este manual também é adequado para os modelos :Fonte de alimentação e fonte de alimentação - P180B (58.61 kb)