Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
9. Clean indicator light illuminates after 30 hours of “on” time to remind you to clean the metal grease filters. The light stays on until the filters are replaced. If the red light stays on and the filters are in, adjust the right-side filter in place. The timer resets automatically. 10. Indicates the time the fan is set to run, before automatically shutting off (5, 10 or 20 minutes). 11. Fan ON indicator light. Fan ControlsLight ControlsFan Control Care and Cleaning Stainless Steel Hood For your safety Before servicing or cleaning the unit, switch power off at the service panel and lock the service panel to prevent power from being switched on accidentally. If the service panel cannot be locked, fasten a tag or prominent warning label to the panel. Charcoal filters (on some models) If the model is not vented to the outside, the air will be recirculated through disposable charcoal filters that help remove smoke and odors. The charcoal filters should be replaced when they are noticeably dirty or discolored (usually after 6 to 12 months, depending on hood usage). NOTE: DO NOT rinse, or put charcoal filters in an automatic dishwasher. The charcoal filters cannot be cleaned. They must be replaced. Order Charcoal Filter Kit (3 filters) WB02X10731. This kit can be ordered from your GE Supplier. NOTE: To remove the metal filters, push them back and down using the knob. Push the charcoal filters back and down Metal Filters For proper operation, be sure to use the charcoal filters in the upper set of filter holders and metal filters in the lower set of filter holders. using the tab. Charcoal Filters Front Metal grease filter Clean the grease filter after 30 hours of “on” time. A signal light will alert you when 30 hours has passed. Remove the grease filters and wash them either by hand or in the dishwasher using non-abrasive soap. Front To clean, swish the filters in hot, soapy water or wash them in the dishwasher. Do not use abrasive cleansers. NOTE: To remove filters, push them back and down using the knob. For proper operation, be sure to use the lower set of filter holders. Hood surfaces Do not use a steel-wool pad; it will scratch the surface. To clean the stainless steel surface, use warm, sudsy water or a stainless steel cleaner or polish. Always wipe the surface in the direction of the grain. Follow the cleaner instructions for cleaning the stainless steel surface. To inquire about purchasing stainless steel appliance cleaner or polish or to find the location of a dealer nearest you, please call our toll-free number: National Parts Center: 800.626.2002 Controls and Features Stainless Steel Hood Light bulbs NOTE: The glass cover should be removed only when cool. CAUTION: Before replacing the bulb, disconnect electrical power to the hood at the main fuse or circuit breaker. Allow bulbs to cool before touching. Be sure to let the light cover and bulb cool completely. For safety, do not touch a hot bulb with bare hands or a damp cloth. To change the light bulbs: 1. Remove the lamp lens cover by inserting a small flat-blade screwdriver into each of the three slots and gently prying it free. NOTE: Do not remove the outer trim ring (lamp assembly). 2. Grasp the bulb and pull it straight out. 3. Using gloves or a dry cloth, remove the new bulb from the packaging. (Wearing latex gloves may offer a better grip.) The bulb must be the same wattage, 120-volt, 25-watt halogen with a G-9 base. Early bulb failure may occur if wattage is too high. 4. Push the bulb straight all the way into the receptacle. 5. Replace the lens cover by inserting the three retaining tabs into the slots and pressing into place. NOTE: For improved lighting, clean the glass cover frequently using a damp cloth. This should be done when the hood is completely cool. 6. Reconnect electrical power to the hood. NOTE: Order replacement 120-volt, 25-watt halogen bulb with G-9 base, WB25X10020. These bulbs can be ordered from your GE supplier. Use a small flat-blade screwdriver to remove the lamp lens cover. Bulb Outer trim ring (lamp assembly) Do not remove Tab Removable inner lamp lens cover NOTE: Make sure the tabs are inserted into the slots. ONLY use a new 120-volt, 25-watt halogen bulb with a G-9 base. Receptacle Use gloves or cloth NOTE: Do not touch the new halogen bulb with bare fingers. Skin oils can cause early lamp failure. The Problem Solver Stainless Steel Hood Questions? PROBLEM POSSIBLE CAUSE Use this problem solver! FAN DOES NOT • A fuse may be blown or a circuit breaker tripped. Replace fuse or OPERATE WHEN reset circuit breaker. THE ON/OFF BUTTON IS PUSHED FAN KEEPS GOING OFF AND ON • The motor is probably overheating and turning itself off. This can be harmful to the motor. Check to be sure the filter is clean. If off and on cycling continues, call for service. FAN FILTER LIGHT IS ON • After 30 hours of “on” or running time, the light reminds you to clean the metal grease filters. The light will glow until the filters are replaced. • T...
Este manual também é adequado para os modelos :Fans - GE Monogram ZV855 (1.12 mb)