Dispose carefully of the packaging material so that it is out of the way of small children. Position The cooker hood should be mounted freely hanging on the wall. The cooker hood must be at least 60 cm above electric hobs or electric ranges, or at least 70 cm above gas burners or gas ranges. The cooker hood cannot be connected to flues of other appliances that run on energy sources other than electricity. Please, keep to the provisions of official directives regarding fume discharge. Electrical

Never use caustic detergents or abrasive brushes or powders. Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents. Attention! Attention! Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. 40 MKZ telescopic wall pipe 120 mm outlet hose KLF60/80 activated carbon filter E-Nr. 610 899 004 610 899 007 610 899 421 Technical assist

Rotate motor upwards until it snaps into the spring clip on the right. Secure the motor to the hood with the machine screw and lock washer. Plug connector into the motor, Fig. 11. From Control Panel Motor connector FIG. 11 FIG. 10 Spring Clip Outlet Bracket Motor Connector Spring Clip Motor support Fixing point Fixing point Bracket Integral ventilator for 40" Hood 11 INSTALLATION 12 2. Snap the central baffle filter panel into the place so the both rails engage with side pins on both sides of ho

When you contact us we need to know: • Your name • Address and post code • Telephone number • Clear and concise details of the fault • Name and model of the appliance* • E number* • This information can be found on the rating plate, which can be seen when the grease filters are removed. Customer Care For general enquiries concerning your AEG appliances, or for further information on AEG products, please contact our Customer Care Department at the address below or visit our website at Cu

Therefore please observe these recommendations. 1) Disconnect the hood from the electricity supply. 2) Remove the filter grille (fig. 3) - this will then allow inspection/ change of the bulb/s. 3) Unscrew defective bulb and replace with new one. Important: always use 40W candle lamp (E14) bulbs. Before calling the Service Engineer because the hood fails to light up, make sure the bulbs are screwed in tightly. Dimensions Height — 400mm Width — 599mm Depth —270mm Weight Net 9,7Kg Connecte

EFB675X | EFB975X | EFB175X SK3060A | SK3090A EFB60X | EFB90X | EFB120X Stylish stainless steel splashbacks to complement stainless steel range of ovens, hobs and hoods. ¦ 75cm high ¦ Available in 60cm width (EFB675X) ¦ Available in 90cm width (EFB975X) ¦ Available in 100cm width (EFB175X) ¦ Easy to wipe clean with rigid reinforced back Stylish Alutec® splashbacks to complement AluTec range of ovens, hobs and hoods. ¦ 75cm high ¦ Alutec® Splashback 60cm wide 75cm high ¦ Alutec® Splashback 90cm w

12 Mounting the cooker hood - Fig. 7 Position the template on the wall and mark the position, and drill the holes (2 x O 8 mm).Mount the two rawl plugs with the hooks (3) Hang the hood on the hooks and level it with the adjustment screws (4) Remove the grease filters (5) and mark for the two screws (6). Remove the hood and drill the holes (2 x O 8 mm). Insert the rawl plugs (7) and hang the hood on the wall again. Adjust it horizontally with the screws (8) and secure it with the screws (9) Mount

In this case the hood will be slightly noisier. Filter Version • The air is filtered through an charcoal filter and returned to the kitchen through the top grill of the outlet pipe. • You will need an original AEG charcoal filter for the filtering function. (See Special Accessories). • Fix the deflector using 2 screws O 2,9x13 mm. Fig. 2. • Optionally, the position of the chimney elements can be changed. When using the hood in the filter version the chimney must be fixed at the top, with the air