Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
• Never leave the appliance unattended, especially if children are present. • Never cover the appliance when it is in operation. • This unit should not be used by children without adult supervision. • Connect the pump with the proper voltage as indicated on the pump label. • Always keep the cord away from high temperature and fire. • Unplug the pump from power source before cleaning, maintenance or disassembling. • To get the best flowing effect, product must be placed surface and should never be placed on an electrical • Never let pump run dry, as this will shorten life of the pump. • Do not lift, carry, hang, or pull the pump by the power cord. • Operate with tap or distilled water only. • Operate pump completely submerged • The electrical cord of this product damage, you must stop using this it to the HoMedics Service Center (See the warranty section for HoMedics address.) • Disconnect the appliance 3 4. Insert the waterproof light into the light hole located on the Assembly and Instructions for Use underside of the panel. (Fig. 3) 1. Unpack the product. Wipe off dust with a damp cloth. Figure 3 2. Familiarize yourself with the pump. The pump speed is con- Attention: In order to get best results, please operate pump completely submerged. Keep the water level above the minimum water level ALL THE TIME. Minimum Water Level Flow Control Valve (+) faster water output (-) slower water output Figure 1 Figure 4 Connector Tube 5. Join the pump outlet and the connector tube under the panel. (Fig. 4) 6. Place the panel on top of the basin. Note: Lead the power cord through the slot located at the top of the basin. This will allow the fountain panel and top to sit evenly on the basin. 7. Insert the top connector into the socket located in the the panel. (Fig. 5) 8. Fill the basin with approximately 3 1/2 cups of water. The pump needs to be completely submerged in water properly. 9. Arrange the rocks on the panel for decoration. for splashing and adjust accordingly. 10. Attach the A/C adaptor jack to 11. Plug the cord into 120V household trolled by the switch located If pump does not operate, rotate in-line turn “off”. Note: Ensure that the electrical cal outlet to form running down Figure 5 Fountain Top trolled by the switch located at the front of the pump. The speed is indicated by a plus (+) and minus (-) sign. To increase the speed, move the switch slowly downward in the direction of the plus sign. You will hear a click as the switch moves to each speed level. At its highest speed level, the switch will cease to move any further. To decrease the pump speed, move the switch upward toward the minus sign. Similarly, at its lowest speed, the switch will cease to move any further (Fig 1). NOTE: It is recommended the pump be set at its highest speed during assembly and later adjusted to a lower setting if desired. Be sure to unplug the pump before adjusting the speed setting. 3. Place the basin on a flat surface. (Fig. 2) 45Figure 2 Waterproof Light Light Hole Fountain Top Socket Water Pump Switch Adaptor Basin Connector Tube Socket Stones Connector Tubes Pump Waterproof Light Light Hole Panel Panel Panel Panel RELAXATION FOUNTAIN Slate Streams ™ PP-ROCKBLB Replacement bulbs and covers for $5.00 WFL-SLST - pack of 5 SUBTOTAL TAX-Michigan Residents add 6% Total Name Address City State Zip Code Phone Number ( ) Detach and return order form with check or money order payable to HoMedics, Inc. Please allow 2 to 4 weeks for delivery. Replacement Parts Order Form PART DESCRIPTION QUANTITY COST Mail To: HoMedics Consumer Relations Service Center Dept. 168 3000 Pontiac Trail Commerce Township, MI 48390 e-mail: cservice@homedics.com 7 6 Troubleshooting • If the pump fails to operate, check the following: Check the circuit breaker, or try a different outlet to make sure the pump is getting electrical power. NOTE: Always disconnect from electrical outlet before handling the pump. • If the pump gurgles, spews, or “burps”: Check the water level to make sure the pump has enough water to function. •Obtaining a desired water level: Check the water level daily the first week to measure the rate of evaporation; refill with water as needed. •If water is splashing outside the fountain: Adjust the flow control valve to a lower setting on the pump. Maintenance • To clean the pump: Unplug from electrical outlet. Remove it from the base of the fountain. Use a small brush or stream of water to remove any debris (Fig 7). • To keep water clean: Periodically change water and clean the product according to the water condition. Keeping the water clean prevents the water from becoming sticky and forming micro-organisms. We recommend distilled water to prevent mineral build-up. • To clean off hard water deposits on the base or stones: Soak the container and rocks in a mixture of vinegar and water to clean and remove any mineral build-up. • Keeping the water at an optimum level: Add water periodically to keep water level at an optimum level to avoid ...
Este manual também é adequado para os modelos :Libra - ENVIRASCAPE WFL-SLST (273.82 kb)