Assessments - , GPA: ( )

Instruções de Operação Audiovox, Modelo 50-0263x-001 SERIES

Fabricante : Audiovox
Arquivo Tamanho: 467.28 kb
Arquivo Nome : 087ce392-0492-4d2a-9c0e-ee1e1a8502f3.pdf

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

Special tools and equipment, as well as specialized handling and care of product during installation, may be required. Before beginning this installation, carefully read through the following instructions. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. 3/8" drill bit 4. Razor knife or similar 5. Awl or similar tool 6. Audiovox VCP (AVP- 7180 or equiv.) MATERIALS PROVIDED FOR INSTALLATION: INSTALLATION INSTRUCTION # 44-0027A Jan. 21, 1999 Printed in the U.S.A ITEM Description 1 SCREW, # 8 X 1 1/2" PWH 2 3 4 5 SCREW, # 8 X 3/4" PPH VCP MOUNTING BRACKET HOUSING TOP HOUSING BOTTOM QTY 4 4 1 1 1 INSTALLATION INSTRUCTION # 44-0027A 2 Jan. 21, 1999 Printed in the U.S.A. REMOVE AND DISCARD (2) TWO SCREWS WHICH SECURE BRACKET TO HOUSING. SEPARATE HOUSING TOP FROM HOUSING BOTTOM. 1. Route video and audio cables to passenger’s side rear of vehicle. Using a razor knife, carefully cut a slit in carpet to allow cables to pass through. Make sure wiring will not rub against edge of bracket. Position VCP mounting bracket (item 3 pg 2) against side panel and 1 1/8" from back edge of ledge on side panel as shown. Make sure bottom of bracket is firmly resting on floor of vehicle. Mark the center of slot on side panel. See Figure 1. FIGURE 1 2. Carefully drill a 3/8" hole in location previously marked. CAUTION: Drill through plastic only, do not drill through sheet metal brace behind plastic. See Figure 2 . FIGURE 2 3. Align slot in VCP mounting bracket with hole previously drilled. Loosely install (1) one #8 x 1 1/2" screw (item 1 pg 2) in dimple in metal brace behind plastic panel. See Figure 3. FIGURE 3 3 4. Remove and discard (4) four screws from the side of VCP. Partially install (4) four #8 x 3/4" screws (item 2 pg 2). See Figure 4. FIGURE 5 6. Carefully position housing top (item 4 pg 2) on VCP and slide VCP rearward until housing contacts plastic panel. Mark position of bracket and remove housing and VCP. Install (3) three #8 x 1 1/2" (item 2 pg 2) in holes in bracket and tighten (1) one screw previously installed. NOTE: Do not overtighten screws. See Figure 6. FIGURE 4 5. Align screws in VCP with slots in bracket and slide into position. Make sure wiring does not rub against edge of bracket. See Figure 5. FIGURE 6 4 FIGURE 7 8. Install housing bottom (item 5 pg 2) and secure to bracket by inserting clips into slots and pressing firmly. Make sure contour of housing matches floor of vehicle prior to securing clips. See Figure 8. 7. Make all necessary wiring connections to VCP. Check function of VCP and video system. See operating instructions included with components. For further assistance, refer to the video system manual for the technical support phone number listed for your area. Install VCP and tighten screws. Make sure VCP screws are positioned at bottom of slot. CAUTION: Do not overtighten screws. See Figure 7. ....., 5...