Assessments - 5, GPA: 4.6
(
)
)
|
Facilidade de uso
Remove and retain (6) six screws which secure CD changer to bracket. See Figure 3. Lay CD changer in a safe place. Discard bracket. FIGURE 2 FIGURE 3 IF VECHICLE IS EQUIPPED WITH A FACTORY 10 DISC CD CHANGER, PROCEED TO STEP 6. 3 5. Locate the O.E.M. storage pocket mounted to the rear passenger side of vehicle. Remove and discard pocket by moving it upward and outward. See figure 4. FIGURE 4 6. Using a pin router, razor knife, or suitable tool, carefully trim plastic panel as shown to allow clearance for VCP bracket. See Figure 5. Caution: Before cutting panel, check for wiring or other componentry behind panel. Cut only where indicated. 7. Install (2) two housing mounting brackets (item 8 pg 2) as shown and secure using (3) three # 8 X 9/16" screws (item 6 pg 2) on each side. See Figure 6. FIGURE 5 FIGURE 6 4 8. Route video and audio cables to rear passenger side VCP location. See Figure 7. FIGURE 7 II. PREPARATION OF COMPONENTS FOR INSTALLATION 9. Remove and discard (2) two screws which secure mounting bracket (item 7 pg. 2) to housing. Insert CD changer (if equipped ) into mounting bracket and secure in original manner using (6) six O.E. screws. See Fig. 8. 10. Remove and discard (4) four screws from VCP. Loosely install (4) four #8 X 3/4” screws (item 1 pg. 2) in those locations. See Figure 9. FIGURE 8 FIGURE 9 III. INSTALLATION OF HOUSING IF VECHICLE IS NOT EQUIPPED WITH A FACTORY 10 DISC CD CHANGER, PROCEED TO STEP 13. FIGURE 10 11. Install CD player and bracket over O.E. studs and secure using original hardware. See Fig. 10. 12. Connect wiring to CD player. 5 IF VECHICLE IS EQUIPPED WITH A FACTORY 10 DISC CD CHANGER, PROCEED TO STEP 16. 13. Align top holes in VCP mounting bracket (item 7 pg 2) with holes in vehicle. See Figure 11. 14. Insert (2) two well nuts (item 2 pg 2) into top holes and secure using (2) 10-32 x 1" screws (item 3 pg 2) and (2) two # 10 washers (item 4 pg 2). See Figure 11. 15. Secure bracket to vehicle using (4) four # 10 X 1/2" screws (item 5 pg 2). 16. Remove and discard storage pocket (item 10 pg 2). Using a razor knife, carefully trim away plastic flange to allow for CD player. See Figure 12. Make diagonal cuts at the corners to make it easier when breaking tabs. 17. Make all necessary wiring connections to VCP. Check function of VCP. See operating instructions included with components. For further assistance, refer to the video system manual for the technical support phone number listed for your area. 18. Align screws in VCP with slots in bracket and slide into position. Make sure screws are positioned at bottom of slot. See Figure 13 . CAUTION: Do not overtighten screws. 19. Install housing bottom (item 11 pg 2) and carefully fold carpet away from each side to gain access to mounting holes. Secure to VCP mounting bracket using (2) two # 8 X 9/16" screws (item 6 pg 2) on each side. Make sure contour of housing matches floor of vehicle. See Figure 14. Carefully tuck carpet behind O.E. plastic panel. 20. Carefully i...
Este manual também é adequado para os modelos :Câmaras de vídeo - 50-0283x-017 SERIES (635.99 kb)
Câmaras de vídeo - 50-0283x-019 SERIES (635.99 kb)