8 [AUDIO OUTPUT] switch Use to select the audio channel to output from the rear panel’s [AUDIO OUT] connectors and the headphones. 9 [VIDEO INPUT/AUDIO MONITOR] switch Use this switch to select the video input signals or to select the audio channel you want to output from the rear panel’s ) [AUDIO MONITOR OUT] connector. % 1 2 3 4 Use No. 054 menu switch to switch between VIDEO INPUT and AUDIO MONITOR. See “ Recording preparation” on page 26. See “ Playback preparation” on page 28. In the REC or FF/REW mode, the [VIDEO INPUT] switch has no effect. Set the [VIDEO INPUT] switch after the REC or FF/ REW operation is complete. 0 [PHONES] jack Connect a set of headphones (3.5 mm dia. mini-jack). ! PHONES control Use to adjust the volume level of the headphones connected to the [PHONES] jack. @ [REC LEVEL] control Use to adjust the audio recording level. CH-1/3: CH1 can be adjusted in normal recording. CH3 recording level can be adjusted in audio dubbing. CH-2/4: CH2 can be adjusted in normal recording. CH4 recording level can be adjusted in audio dubbing. Audio dubbing is possible when the No. 245 menu switch is set to “ 32K” . # Setting buttons Use to set the menu switch, time code and user bits. Menu switch setting MENU: Press to set the menu switch setting mode. SHIFT +/ – : Use to select the menu switch. SET: Use to enter the set value. SELECT: Use to change the value. Time code and user bits setting HOLD: Press to set the time code, user bits or time date setting mode. SHIFT: Use to select the digit whose value is to be changed. ADVANCE: Use to change the value. While pressing the [SHIFT] button, press this button to reset the set data to “ 0” . PRESET: Use to enter the changed value and end setting. Use as a counter reset button when the [COUNTER] switch is set to “ CTL” . $ [AUDIO DUB] button Use to perform audio dubbing when the No. 245 menu switch is set to “ 32K” . % Cassette loading slot Load and unload a cassette. 2 CONTROLS, CONNECTORS AND DISPLAYS 2-2 Rear panel ^ & % $ # @ ! 0 9 876 5 1 AC socket Connect the provided power cable to supply AC 120 V (U MODEL), AC 220 V – 240 V (E MODEL). This unit can be activated automatically when power is supplied according to the setting of 7 [TIMER] switch. See “ EXTERNAL TIMER-START FUNCTION” on page 30. 2 DC socket Connect DC 12 V (XLR 4-pin). This unit can be activated automatically when power is supplied according to the setting of 7 [TIMER] switch. See “ EXTERNAL TIMER-START FUNCTION” on page 30. 3 [REMOTE] connector (JVC bus) This unit can be controlled by the RM-G800 via this connector. 4 [REMOTE] connector (RS-422 Serial Connector) This unit can be controlled by an RS-422 controller. This can be changed to an RS-232C interface if required. For details, contact your local JVC service center. 5 [REMOTE] connector (SERIAL) Connect a wired remote control such as the RM-G30 to control this unit. 6 [TIME CODE IN] connector Input the time code signal from a time code generator to this connector. To use this connector, set No. 413 menu switch to “ EXTERNAL” . See “ TIME CODE: Recording” on page 33. 7 [TIMER] switch Use to select the timer operation. REC : Timer recording OFF : Timer function OFF PLAY : Timer playback See “ EXTERNAL TIMER-START FUNCTION” on page 30. 8 [TIME CODE OUT] connector Use to output time code signals. During playback, playback data is output while generator data is output during recording. * ( ) 1 2 4 3 9 [SYNC IN] connector Input reference sync signals. See “ Reference sync signal” on page 12. 0 [VIDEO MONITOR OUT] connector Connect a video monitor to check the output video or on-screen display from this unit. ! [Y/C OUT] connector Outputs Y/C signals. @ [LINE OUT] connector Outputs composite signals. # [Y/C IN] connector Receives Y/C signals. $ [LINE IN] connector Receives composite signals. % [DV IN/OUT] connector Outputs or receives IEEE 1394 standard digital signals. In addition to video, audio and time code signals, control signals can be input or output to/from a personal computer provided with the DV connector (i.LINK), etc. ^ [COMPONENT IN] connectors Receive component signals. The signal level is for Betacam specifications. & [COMPONENT OUT] connectors Output component signals. The signal level is for Betacam specifications. * [AUDIO IN] connectors Receives audio signals (analog). ( [AUDIO OUT] connectors Outputs audio signals (analog). The output audio channel can be selected with the 8 [AUDIO OUTPUT] switch on the front panel. See “ Audio system connections” on page 13. ) [AUDIO MONITOR OUT] connector Connect to the audio input of a TV monitor or audio system. The audio channel to be monitored can be selected with the 9 [AUDIO MONITOR OUT] switch. 2 CONTROLS, CONNECTORS AND DISPLAYS 2-3 On-screen display The on-screen display can be viewed on a monitor connected to the rear panel’s [VIDEO MONITOR OUT] connector when the No. 500 menu switch is...
)
