Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
If this is the case, wait two to three hours before removing the cassette. (2) Wait two to three hours with the cassette holder open. The time you need to wait depends on the amount of condensation and the ambient temperature. (3) Turn on the power two to three hours later and check whether or not the condensation display has gone off. To make doubly sure, wait another hour or so after the condensation display has gone off before using the camera-recorder again. Also remember that even when the condensation display has not appeared, condensation may be forming. • Condensation builds up gradually so the condensation display may not appear for 10 to 15 minutes after it has started to form inside. In very cold areas, the condensation may freeze. If this happens, it will take another two to three hours for it to thaw out. Reference 125 126 Eye cup holder Eye cup Projection System resetting Reset the system microcomputer if you can no longer operate the camera-recorder even though its power is on or a similar kind of a problem has occurred. Use a pointed object to press the RESET button on the camera-recorder. The menu setting entered and memory contents will not be cleared even when the system is reset. Do not press the RESET button when the camerarecorder is operating normally. Cleaning When cleaning, do not use benzene or thinner. • Using benzine or paint thinners may deform the camera-recorder and/or cause the surface finish to peel off. • Before proceeding with maintenance, remove the battery or disconnect the AC cord from the power outlet. • Use a soft, clean cloth to wipe the camerarecorder. To remove stubborn dirt, wipe the camera-recorder with a cloth moistened with kitchen detergent that has been diluted with water and then use a dry cloth to take up the remaining moisture. Cleaning the Viewfinder If there is dust inside the view finder, remove the eye cup holder and get rid of the dust. • The interior of the eye cup holder is specially finished, so do not ever wipe it. If there is dust on it, blow it off with an air blower. • Remove the eye cup holder with the eye cup attached by rotating it counterclockwise. (It will be tightly screwed on.) When you do this, tilt the view finder slightly upward. • To amount the eye cup holder, align the ridges and grooves of the eye cup holder and camerarecorder, and turn clockwise until the holder clicks into place. CH 1 SELECT CH 2 SELECT INPUT 1 INPUT 2 INT(L) INPUT 1 INPUT 2 INT(R) INPUT 2 ON OFF BARS AUDIO SHUTTER SPEED SEL COUNTER RESET/TC SET ZEBRA OIS RESET ON OFF MIC POWER +48V RESET button Video Heads Dirty video heads cause partial mosaic-pattern noise or make the whole display bluish on playback. When the video heads get extremely dirty, the recording quality decreases, and, in the worst case, it won’t record at all. Causes of dirty video heads • Dusty atmosphere • High temperature and humidity • Scratches on tapes • Overuse Using A Cleaning Tape (Page 133, OPTIONAL UNITS) (1) Insert the cleaning tape in the camera recorder and turn on the power switch. (2) Press the mode button and make sure the VCR lamp is on. (3) Press the operation button . Press within ten seconds. (Do not rewind the tape at this point.) (4) Eject the cleaning tape and insert another tape. Record on it and play it back. Make sure the picture is fine. (5) If the picture is not clear, repeat the steps 1-4. (Do not use the cleaning tape more than four times in a row.) • Do not rewind the cleaning tape until it gets to the end of the tape. When the tape gets to the end, rewind it to the beginning to use it again. • If the video head gets dirty soon after you clean it, the cleaning tape might be damaged. Stop using the cleaning tape right away. • Overusing the cleaning tape might damage the video head. If the video head is damaged, the picture quality will not improve even when you clean the video head. • When you can’t clean a dirty video head with the cleaning tape, it needs cleaning and repair at the dealer. Please contact them. Regular Maintenance For the superior picture quality, we recommend replacing consumable parts such as a video head approximately every 2,000 hours of use. (However, this estimated time varies greatly depending on the environment in which it is used, such as temperature, humidity, and dust.) Reference 127 Storage Precautions Before storing the video camera, remove both the cassette and battery. Store all of these items in a place with low humidity and relatively constant temperature. [Recommended temperature range: 15°C to 25°C (59 °F to 77 °F )] [Recommended relative humidity: 40% to 60%] Video camera • Wrap the video camera in a soft cloth to keep the dust off. Battery • The battery life is shortened in places with extreme temperatures. • Storing the battery in a location with oily vapors or high dust concentrations may corrode the terminals or cause other damage, leading to malfunction. • Keep metal objects (such as necklaces and hair pins) away from the term...