Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
59:50 t_I (return to 0:00 and continue) • The 10-Second Reminder will be reset whenever you press Record/Pause. @ TAPE SPEED Indication (see page 10) Indicates the tape speed (SP or SLP). ® Operating Mode Indications REC (record) (RECORD will first appear in large characters for one second and then small characters.) PAUSE (PAUSE will first appear in large characters for one second and then small characters.) FF (fast forward) PLAY REW (rewind) 1 2:00 :00AML JAN 1 1 995] Electronic Viewfinder Indications HVCR-MODFl FÀ P El- ©Í1 2:0 0 :0 0 A M l ~|JAN 1 1 995] © © © Backlight Indication (see page 29). (?) Manual Focus Indication (see page 28). (D Fade Indication (see page 27). (D Zoom Magnification level (see page 27). © High Speed Shutter Indication (see page 29). ® VCR-MODE Indication “VCR-MODE” will appear for one minute if the POWER switch is set to VCR or the RECORD/PAUSE button is pushed in VCR MODE. © DEW Indication If excessive moisture condenses in the unit, “WARNING” and Power Lamp will flash, “DEW DETECTED" will appear, and the Palmcorder will automatically turn OFF in 15 seconds. In this case, wait until the indicator no longer flashes when your Palmcorder is turned on before using your Palmcorder again. © Date and time Indication (see page 13). 17 Getting Started Attaching the Shoulder Strap Make sure the Battery Pack is not attached. Unthread the strap from the buckle. ' Thread the strap ends through the Strap Attachment Rings. ™j07rnjmTti min. 1 inch 1 Then thread the ends of the strap through the buckle. • Make sure the strap is not twisted. Adjust the Length Hand Strap Pull a loop of the strap loose from the buckle. Pull the strap firmly through the buckle to adjust the length. Camera Recording Simple Recording Tally Lamp Before you begin... • Connect the Palmcorder to a power source. • Insert a cassette with record tab (see page 10). Set the POWER switch to CAMERA. Built-In Lens Cover opens. EVF TAPE EJECT Note: • Do not leave the Palmcorder with the EVF aimed directly at the sun as this may cause damage to the Internal parts of the EVF. Record/Pause mode. With the Viewfinder Eye Cup up to your eye, adjust the Vision Adjustment Control to your eyesight. Slide the TAPE SPEED Selector to SP or SLP (refer to page 10). Press RECORD/PAUSE to start recording. The Tally Lamp and RECORD/PAUSE are lit during recording. RECORD Press RECORD/PAUSE again tQ pause recording. Set the POWER switch to OFF after recording is finished. * To remove the cassette In Record/Pause mode, slide the TAPE EJECT switch (refer to page 10). When your Palmcorder is aimed at excessively bright objects, or bright lights, a vertical bar may appear in the picture. This is a normal characteristic of the CCD pick-up device. Try to avoid this when possible. 19 Basic Operation Camera Recording Stand-by Mode Whenever the Palmcorder has been in Record/Pause mode for 5 minutes, it will automatically go into Stand-by mode to conserve power. To resume recording, it is necessary to turn the Palmcorder POWER switch to OFF and then to CAMERA. Or, you may use the following feature to avoid having to turn the Palmcorder off and on again. Stand-by Release This feature allows you to resume recording from Stand-by mode by simply pressing the RECORD/PAUSE button. Before you begin... • Connect the Palmcorder to a power source. • Insert a cassette with record tab (see page 10). DISPLAY While pressing the UP A button, set the POWER switch to CAMERA. Press UP A more than 2 seconds to display the STAND-BY RELEASE selection screen. STAND-BY RELEASE BY HE CORO/PAUSE KEY ACTIVE CEB2HZB3 SELECT: PUSH T/A KEY VSET : PUSH DISPLAY KEY RECORD/PAUSE Press UP A or DOWN ▼ as necessary to select QiQQl. Press DISPLAY to set your selection and exit this screen. • You may now turn the Palmcorder back on after it has gone into Standby mode by pressing the RECORD/ PAUSE button. Note: If was selected in step 3 above, you must set the POWER switch to OFF and then to CAMERA to resume recording from Stand-by mode. 20 Camera Recording Easy Edit Stand-by If you stop recording but plan to resume within 24 hours, use the Edit Standby feature to make a smooth transition between scenes. Set the POWER switch to OFF and leave the cassette in the Palmcorder. Set the POWER switch to CAMERA and press RECORD/PAUSE (within 24 hours) to continue recording. Note: • 11 it is going to be longer than 24 hours before you resume recording, use the manual Easy Edit feature described below. POWER Switch Manual Easy Editing For proper continuity when taping from the Stop mode, or after changing the Battery Pack. Set the POWER switch to VCR. ® Press REWIND/SEARCH to go back a few seconds on the tape. (§) Press PLAY to review the picture on the Viewfinder. © Press STILL at the location you wish to continue your recording. Set the POWER switch to CAMERA. Press RECORD/PAUSE to continu...