Assessments - 4, GPA: 4
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
Slide the lock to the OPEN side and lift the projection with a finger to open. 2 Insert/Remove the SD card. • To insert: Face the label upwards and slide the card in straight until hearing it catch. • To remove: Press the center of the SD card and pull the card out straight. 3 Close the card/battery door. •Press [ ] until hearing the door snap closed. •If the door does not close completely, remove the SD card, Check that the red marker of check its orientation and reinsert it the lock is no longer visible. into the slot. OPEN OPEN Place label upwards. Projection Press here. .While the card access lamp is lit, reading, recording, playback, deletionor other processing is being executed. Performing the followingoperations while the lamp is lit may damage the SD card and its contentand the unit may not function properly. • Switching off power • Removing battery or AC adaptor • Opening card/battery door and removing SD card • Rotating the mode dial • Shaking or impacting the unit Card access lamp VQT1M21 Setup 4 Turning power ON/OFF(Selecting modes) Setup 4 Turning power ON/OFF(Selecting modes) Rotate the mode dial slowly but surely to the desired position without turning it recklessly. Set to icon of desired mode. Power OFF Motion picture recording mode (P.34) Motion picture playback mode (P.52) Still picture recording mode (P.36) Still picture playback mode (P.55) Status indicator • When power is ON: Lit red (When selecting ) • When power is OFF: Off .The very first time that power is turned ON, a message appears prompting you to set the date and time. (P.30) Turning power ON/OFF from the LCD monitor When [ ] or [ ] is selected, power turns ON when the LCD monitor is opened and OFF when it is closed. (During motion picture recording, power does not turn OFF when the LCD monitor is closed.) • When [QUICK START] (next page) is [ON], the unit goes on quick start standby when the LCD monitor is closed. • When not in use, set the mode dial to [OFF]. VQT1M21 Rotate the mode dial to motion picture recording/playback, still picture recording/playback or power OFF. Quick starts Quick starts are available when the mode is set to [ ] and [ ]. When [QUICK START] is [ON], the unit responds as follows to LCD monitor operations: LCD monitor operation Unit response Status indicator When opened Shooting can start in approx. 0.6 second. Lit red When closed The unit goes on quick start standby* . Flashing green * The unit consumes about half as much power as when recording is stopped. Setting [QUICK START] Make settings from themenus. (P.28) >[SETUP]>[QUICK START]>[ON] (To turn OFF, select [OFF].) • [QUICK START] is [ON] at the time of purchase. .The quick start standby is canceled and power shuts OFF (status indicator out) in the following situations. • When quick start standby mode continues for more than about 5 minutes • When the mode dial is rotated .When white balance is set to [ ], quick starts require more time if the light source differs from that prior to quick starting, because automatic adjustments are performed. (However, automatic adjustments are not performed when using the MagicPix function.) .Starting may require more time than usual if the unit is impacted. .Zoom magnification becomes 1x after quick starts. .If [POWER SAVE] (P.84) is set to [5 MINUTES] and the unit automatically goes on quick start standby, close and reopen the LCD monitor. VQT1M21 Setup 5 Setting from the menu Setup 5 Setting from the menu The menu cannot be displayed during recording or playback. For menu items (P.82 “Menu List”) To return to the previous screen To quit an operation halfway through 1 Display the menu. The menu displayed differs according to mode. 2 Select the top menu. (Top menu for [ ] and [ ] modes) or 3 Enter the top menu. 4 Select a submenu. 5 Enter the selected submenu. or VQT1M21 The cursor buttons are used to select functions, execute operations and make menu settings. 6 Select an item. 7 Enter the selected item. 8 Close the menu. Using the cursor buttonsThe cursor buttons are used to select and enter items on menus or thumbnail displays. Upwards Downwards Left Right .To move the cursor The cursor moves in the direction of the respective cursor buttons when pressed. .Pressing the center enters the selection. .Do not rotate the mode dial while menus appear on the LCD monitor. .You cannot record or perform other operations while menus appear on the LCD monitor. VQT1M21 Setup 6 Setting the date and time, changing the display language Before recording, check that the date and time have been set. The very first time that power is turned ON, a message appears prompting you to set the date and time. Select [YES], press the center of the cursor buttons Setting the date and time and proceed to step 3 . To change the date and time display .To change an item >[SETUP]> [DATE/TIME] [OFF] : Date and time are not displayed. [D/T] : Date and time are displayed. [DATE] : Only the date is displayed. .To change the date format >[SETUP]> ...