0: DVCPRO mode 1: DV mode 2: DVCAM mode The cassette tape is played back in one of the modes listed below depending on the tape type and settings used. Type FORMAT SEL setting DVCPRO DV DVCAM S size cassette DV DV DVCAM M size cassette DVCPRO DVCPRO DVCPRO L size cassette DVCPRO DV DVCAM Use tapes specially designed for DVCPRO applications with this unit. However, if DV tapes or DVCAM tapes are to be used in the playback mode, it is recommended that playback be limited to as short a period of time as possible. 109 REC INHIBIT 0000 OFF This selects whether to inhibit recording on the VTR. 0001 ON 0: Recording is not inhibited. 1: Recording is inhibited. The underlined number and item are the factory settings. INTERFACE menu Item Setting Description of settings No. Superimposed display No. Superimposed display 200 BAUD RATE 0000 0001 0002 Q003 0004 1200 2400 4800 mo 19200 This sets the RS-232C transfer rate (baud rate). 201 DATA LENGTH 0000 0001 8BIT 7BIT This sets the RS-232C data length. 202 STOP BIT QQOO 0001 1BIT 2BIT This sets the RS-232C stop bit length. 203 PARITY Q00Q 0001 0002 NONE ODD EVEN This sets whether the RS-232C parity bit is to be used and, if so, whether with even or odd parity. 0: The parity bit is not used. 1: The parity bit is used with odd parity. 2: The parity bit is used with even parity. 204 ACK RETURN 0000 0001 OFF ON This sets the RS-232C return data. 0: The ACK code is not returned. 1: The ACK code is returned. The underlined number and item are the factory settings. After the settings of items No.200 through No.203 have been changed, the new settings will not take effect until the power is switched on. This means that the power must be turned off and back on again after these settings are changed. 26 Set-up Menus MEMORY MODE menu Item Setting Description of settings No. Superimposed display No. Superimposed display 300 MEMORY MODE 00QQ 0001 0002 0003 OFF MEM STOP REPEAT 1 CONTINUE This sets the memory operation. 0: No memory operation. 1: The tape stops near the BEGIN point when it is.fast forwarded or rewound. 2: When the tape reaches the end, it is rewound to the BEGIN point where it stops. 3: When the tape reaches the end, it is rewound to the BEGIN point where it is played, and this process is repeated. 301 BGN/END PRESET This sets the BEGIN point and END point. The underlined number and item are the factory settings. TAPE PROTECT menu Item Setting Description of settings No. Superimposed display No. Superimposed display 400 STILL TIMER 0000 0001 0002 0003 0004 00QÇ 0.5S 5S 10S 30S 1MIN 2MIN This selects the time taken until the unit is set to the tape protection mode when it has been left standing in the stop, play pause or still mode. (Units: S = seconds, MIN = minutes) • The setting for the time taken until the unit is set to the tape protection mode when it has been left standing in the REC PAUSE mode is fixed at 2 minutes. 401 SRC PROTECT 0000 0001 $TEP HALF This sets the tape protection operation which is performed when the unit has been left standing in the pause mode. 0: Step (step FWD in the still or pause mode; step REV in the REC pause mode) 1: Half loading (standby OFF) 402 DRUM STD BY 0000 0001 OFF ON This sets whether or not the drum is to be stopped in the STANDBY OFF mode. 0: The drum rotates at all times. 1: The drum is stopped in the STANDBY OFF mode. 403 STOP PROTECT 0000 0001 STEP HALF This sets the tape protection operation to be performed when the unit is left standing in the STOP mode. 0: Step 1: Half loading The underlined number and item are the factory settings. When using a consumer DV cassette tape, tape protection mode is set after 10 seconds, even if STILL TIMER is set to “30S”, “1 MIN” or “2MIN”. 27 Set-up Menus TIME CODE menu Item Setting Description of settings No. Superimposed display No. Superimposed display 500 VITC POS-1 0000 0001 0006 0010 10L 11L 1SL 20L This sets the position where the VITC signal is to be inserted. (The same line as that selected for VITC POS-2 cannot be selected.) 501 VITC POS-2 0000 0001 0008 0010 10L 11L JSL 20L This sets the position where the VITC signal is to be inserted. (The same line as that selected for VITC POS-1 cannot be selected.) 502 VITC BLANK 0000 0001 BLANK THRU This sets whether the VITC signal is to be output. 0: VITC signal is not output. 1: VITC signal is output. 503 TCG REGEN 0000 0001 0002 TC. UB TC UB This selects the signal to be regenerated when the TCG is in the REGEN mode, (item No. 507) 0: Both the time code and user’s bit are regenerated. 1: Only the time code is regenerated. 2: Only the user’s bit is regenerated. 504 BINARY GP Q000 0001 0002 0003 0004 0005 0006 0007 000 001 010 011 100 101 110 111 This sets the status for using the user’s bit of the time code generated by the TCG. 0: NOT SPECIFIED (character set is not used) 1: ISO CHARACTER (8-bit character set complying with IS0646 and IS0202...
)
Log: