Assessments - 1, GPA: 5 ( )

Fabricante : Panasonic Arquivo Tamanho: 3.01 mb Arquivo Nome : AJD640P.PDF Língua de Ensino:

(Unit: s = second, min = minute) With the DV or DVCAM format, the maximum time which can be set is 10s even when a setting above 10s has been selected. The selection screen, however, will operate for up to 2 minutes. 401 SRC PROTECT 0000 0001 STEP HALF This selects the operation during the tape protection mode when the unit is left standing in the still status in No. 400 protection mode. 0: STEPFWD. 1: HALF LOADING. When STEP FWD is selected, the unit automatically goes into the HALF LOADING mode when the total time for which the unit is left standing in the still status reaches 30 minutes (DVCPRO) or 1 minute (DV or DVCAM). The underline on the setting item denotes the initial setting. In order to protect the tape and VTR helical heads, it is recommended that the Still Timer be set lor automatic tape protection mode in 30 seconds or under. -33- Setup (setting) menus USER menu Item Setting No. Superimposed display No. Superimposed display Description 500 VITC POS-1 0000 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 10L 11L 12L 13L 14L 15L 16L 17L 18L 19L 20L This sets the position where the VITC signal is to be inserted. (The same line as for VITC POS-2 in 501 cannot be selected.) 501 VITC POS-2 0000 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 10L 11L 12L 13L 14L 15L 16L 17L 18L 19L 20L This sets the position where the VITC signal is to be inserted. (The same line as for VITC POS-1 in 500 cannot be selected.) 502 VITC BLANK 0000 0001 BLANK THRU This selects whether to output the VITC data to the positions selected by VITC POS-1 in 500 and VITC POS-2 in 501. 0: Data is not output. 1: Data is output. 503 TCG REGEN 0000 0001 0002 TC&UB TC UB This selects the signal to be regenerated when the time code generator (TCG) in the REGEN mode. 0: Both the time code and user bit are regenerated. 1: Only the time code is regenerated. 2: Only the user bit is regenerated. 504 REGEN MODE 0000 0001 OFF ON This selects whether values used in the internal time code generator are preset from the front panel or remote controller or synchronized with time code values read from the tape. 0: Values are preset from the front panel or remote controller. (PRESET) 1: Values are synchronized with time code values read from the tape. (REGEN) When “1” is selected, values selected at set up menu No.503 (TCG REGEN) are regenerated. 505 EXT TC SEL 0000 0001 LTC VITC This selects the time code to be used when an external time code is to be used. 0: The LTC of the TIME CODE IN connector is used. 1: The video signal VITC is used. 506 BINARY GP 0000 0001 0002 0003 0004 0005 0006 0007 000 001 010 011 100 101 110 111 This sets the usage status of the user bit of the time code generated by the TCG. 0: NOT SPECIFIED (character set not specified) 1: ISO CHARACTER (8 bits character set based on IS0646, IS02022) 2: UNASSIGNED 1 (undefined) 3: UNASSIGNED 2 (undefined) 4: UNASSIGNED 3 (undefined) 5: PAGE/LINE 6: UNASSIGNED 4 (undefined) 7: UNASSIGNED 5 (undefined) The underline on the setting item denotes the initial setting. -34- USER menu (continued) USER menu Item Setting No. Superimposed display No. Superimposed display Description 507 PHASE CORR 0000 0001 OFF ON This selects whether to control the phase correction of the LTC generated by the TCG. 0: Phase correction control is not performed. 1: Phase correction control is performed. 508 TCG CF FLAG 0000 0001 OFF ON This selects whether the CF flag of the TCG is to ON. 0: CF flag is OFF. 1: CF flag is ON. 509 DF MODE 0000 0001 DF NDF This selects the DF/NDF mode for CTL and TCG. 0: Drop frame mode. 1: Non-drop frame mode. No.509 is valid when the CONTROL is LOCAL or LOCAL ENA of item 004 to “ENA”. 510 RUN MODE 0000 0001 REC FREE This selects the time code generator run mode. 0: Generator runs only during recording. 1: Generator runs during usual operation. Even if “0" is selected, the time code generator runs during usual operation when "I" is selected at the setting menu No.504 (REGEN MODE). 511 TC OUT REF 0000 0001 VOUT TC IN This is used to switch the phase of the time code, which is output from the TIME CODE OUT connector, for the external LTC input when the TC INT/EXT switch is at the EXT position. (In EE mode only) 0: Time code is synchronized with output video signal. 1: Time code is synchronized with external time code input. The underline on the setting item denotes the initial setting.

Baixe o seu

Para fazer o download, introduza 2 dígitos :