Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
13 3-6-1. Auto-Tracing White Balance Mode (ATW) In the ATW mode the color temperature of the illuminant is continuously monitored and the white balance of the camera is automatically set. The ATW mode has a range of operation from approximately 2600°K - 6000°K. Beyond this range, use the Automatic White Balance (AWC) mode. The ATW mode might not produce optimum color rendition in the following conditions. 1. When the scene consists mostly of strongly colored objects or illumination such as a blue sky or during sunset. 2. When the scene is dimly lit. In these cases, use the AWC mode. 3-6-2. Automatic White Balance Control Mode (AWC) In this mode, accurate white balance may be obtained within a range of operation from approximately 2300°K -10000°K. Note: Refer to the SETUP OPERATION section for detailed procedure. 3-7. Special Menu (SPECIAL) The chroma level, chroma phase (HUE), aperture level and pedestal level of this camera can be adjusted by using this special menu. Note: ^ Refer to the SETUP OPERATION section for detailed procedure. ** SPECIAL ** CHROrM GAIN ■■■I■ HUE • • • I • ■ AP GAIN ----I PEDESTAL -1---- RET END Fig. 14 -24 4. SETUP OPERATION Before entering the Setup menu, remember the ALL RESET operation in order to escape from the confusion of setting up the each item to the factory setup condition as follows. (1) Confirm that the normal camera picture is displayed and no setup menu is displayed. (2) While pressing both the Left Switch {<) (9) and Right Switch (>) (8) together, press the Set Switch (11) for a while in order to reset all adjustments and selections to the factory setup condition. ^— Up Switch {10) Right Switch (8) -Down Switch (7) Fig. 15 Note: While the ALL RESET mode is being processed, picture may be disturbed. This phenomenon is normal and indicating the sign of the all reset mode. ® (m Left Switch (9) Set Switch {11 )- Ö 4-1. Entering Setup Menu • By pressing the Set Switch (11) for more than 1' second, the "SET UP" menu is displayed on the monitor screen as shown in Fig. 16. ** SET UP ** CAHERA ID ALOELC SHUTTER AGC SVhIC UH1TE BAL ALC OFF ON INT ATU END SET UP DISABLE Blinking Fig. 16 By observing this menu, you can check the current conditions. Refer to the following sections for details of each item. After confirming current conditions and further resetting of each item is not required, move the cursor to the "END" position on the left bottom line and press the Set Switch (11) to return to the normal camera picture mode. ** SET UP +* CAMERA 10 ALC'ELC SHUTTER AGC SVNC WHITE BAL OFF ALC OFF ON INT ATU SET UP DISABLE Fig. 17 Important Notice When “SET UP DISABLE” is displayed on the bottom line of the Setup menu, you can not enter the actual mode setting. This prevents mis-operation of the mode setting. *■** SET UP ** CAttERA 10 ALC'ELC SHUTTER AGC SVNC UHITE BAL BO ALC OFF ON INT ATU SET UP DISABLE Fig. 18 - 25 - • To enable the setup menu editing (resetting/ readjustment), move the cursor to the bottom line by using the Up Switch (A) (10) and Down Switch (V) (7) and move it to the "SET UP DISABLE" position by using the Right Switch (>) (8) and Left Switch (<) (9) and press the Set Switch (11) and "SET UP ENABLE' is displayed. Press the Press the Right Switch. Set Switch. Fig. 19 • Move the cursor to the desired item to be reset or readjust through the ’END" position. -26 • When the Special Menu is needed to be adjusted, move the cursor to the "END" position and press both the Left Switch (<) (9) and Right Switch (>) (8) together for approximately 2 seconds to display the Special Menu. (Refer to the 8. SPECIAL MENU on page 45.) r “\ +•)■ SPECIAL *• CHROMA GAIN ■■-■I U| C . . , T . AP GAIN ----I PEDESTAL ■I■■■ + RET EHO / Fig. 20 Important Notice: When the cursor is moved to the next position (next item) after changing the data (ex. ON —* OFF), the latest data is written on the memory (Electronic Erasable Programmable Read Only Memory (EEPROM)) and it remains until the further data write is made even if the camera power is switched off. 4-2. Camera Identification (CAMERA ID) Setting • Move the cursor to the "CAMERA ID” mode position, and select either 'ON” (Camera Identification character is displayed) or ”OFF" mode by using either the Left Switch (<) (9) or Right Switch (>) (8). *+ SET UP ■** CAMERA ID OFF. 4» ALC'ELC ALC ^ SHUTTER OFF AGC ON SVNC INT WHITE BAL ATU END SET UP ENABLE Fig. 21 • Move the cursor to the next item to write the new data into the memory. • When the camera identification character needs editing, perform the following steps by using the submenu of Camera Identification. • Move the cursor to the ’CAMEFIA ID’ mode position and press the Set Switch (11) to display the Character Editing menu as shown in Fig. 22. Editing Cursor Character Cursor X_. 3CDEFGHI JKLfl ^ÖPQRSTUUUXVZ □123936789 () . . ' ♦ -> SPACE POSI RET END -Characte...