Assessments - 1, GPA: 3
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
• You record the tape on an AFM HiFi monaural video recorder, then play it back on this camcorder. Foreign 8 mm video Because the TV colour systems differ from country to country, you may not be able to play back foreign pre-recorded tapes. Refer to the list of “Using your camcorder abroad” to check the TV colour system of foreign countries. Usable cassettes and playback modes Usable cassettes and playback modes Playing back an NTSC-recorded tape You can play back tapes recorded in the NTSC video system using the SP mode. If the tape is recorded in the AFM HiFi system, the AFM HiFi sound is reproduced. However, note that the following will occur during playback of an NTSC-recorded tape. • When playing back a tape on a TV screen, you may not get the original colour depending on the TV. When you play back on a Multi System TV, set NTSC PB to the desired mode in the menu system. • During playback, a black band appears on the lower part of the viewfinder. • You cannot play back a tape recorded in NTSC video system with LP mode neither on the LCD nor on a TV screen. • If a tape has portions recorded in PAL and NTSC video systems, the tape counter reading is not correct. This discrepancy is due to the difference between the counting cycle of the two video systems. • You cannot edit the NTSC-recorded tape onto another VCR. Tips for using the battery pack Additional This section shows you how you can get the most out of your battery pack. Preparing the battery pack Always carry additional batteries Have sufficient battery pack power to do 2 to 3 times as much recording as you have planned. Battery life is shorter in a cold environment Battery efficiency is decreased, and the battery will be used up more quickly, if you are recording in a cold environment. To save battery power Turn STANDBY down when not recording to save battery power. A smooth transition between scenes can be made even if recording is stopped and started again. While you are positioning the subject, selecting an angle, or looking through the viewfinder lens or on the LCD screen, the lens moves automatically and the battery is used. The battery is also used when a tape is inserted or removed. When to replace the battery pack While you are using your camcorder, the remaining battery indicator decreases gradually as battery power is used up. The remaining time in minutes also appears. When the remaining battery indicator reaches the lowest point, the iindicator may appear and start flashing in the viewfinder or on the LCD screen. When the iindicator changes from slow flashing to rapid flashing while you are recording, set the POWER switch to OFF on the camcorder and replace the battery pack. Leave the tape in the camcorder to obtain a smooth transition between scenes after the battery pack has been replaced. Tips for using the battery pack Tips for using the battery pack Notes on the rechargeable battery pack Caution Never leave the battery pack in temperatures above 60°C (140°F), such as in a car parked in the sun or under direct sunlight. The battery pack heats up During charging or recording, the battery pack heats up. This is caused by energy that has been generated and a chemical change that has occurred inside the battery pack. This is not cause for concern and is normal. Battery pack care • Remove the battery pack form the camcorder after using it, and keep it in a cool place. When the battery pack is installed to the camcorder, a small amount of current flows to the camcorder even if the POWER switch is set to OFF. This shortens battery life. • The battery pack is always discharging even when it is not in use after charging. Therefore, you should charge the battery pack right before using the camcorder. The switch on the battery pack This switch is provided so that you can mark the charged battery pack. Set the switch to the “green mark” position when charging is completed. (When removed from the charging adaptor, the switch exposes the green mark. When removed from your camcorder, no mark is indicated.) The life of the battery pack If the battery indicator flashes rapidly just after turning on the camcorder with a fully charged battery pack, the battery pack should be replaced with a new fully charged one. Charging temperature You should charge batteries at temperatures from 10°C to 30°C (from 50°F to 86°F). Lower temperatures require a longer charging time. Tips for using the battery pack Tips for using the battery pack Notes on the “InfoLITHIUM” battery pack What is “InfoLITHIUM” The “InfoLITHIUM” is a lithium ion battery pack which can exchange data with compatible video equipment about its battery consumption. Sony recommends that you use the “InfoLITHIUM” battery pack with video equipment having the mark. When you use this battery pack with video equipment having the mark, the video equipment will indicate the remaining battery time in minutes*. However, if you use it with video equipment not having this mark, the remaining battery capa...