Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Placas Gráficas - GV-R467D3-512I (3.93 mb)
Placas Gráficas - GV-R467D3-512I (3.69 mb)
Facilidade de uso
The operator should be wearing an anti-static wristband, grounded at the same point as the anti-static mat. Inspect the card carton for obvious damage. Shipping and handling may cause damage to your card. Be sure there are no shipping and handling damages on the card before proceeding. DO NOT APPLY POWER TO YOUR SYSTEM IF THE GRAPHICS CARD IS DAMAGED. In order to ensure that your graphics card can work correctly, please use official GIGABYTE BIOS only. Using non-official GIGABYTE BIOS might cause problem(s) on the graphics card. GV-R4600 Series Graphics Accelerator - 8 2.2. Hardware Installation Now that you have prepared your computer, you are ready to install your graphics card. Step 1. Locate the PCI Express x16 slot. If necessary, remove the metal cover from this slot; then align your graphics card with the PCI Express x16 slot, and press it in firmly until the card is fully seated. Make sure that the gold edge connector of the graphics card is securely inserted. Step 2. Replace the screw to fasten the card in place, and replace the computer cover. Step 3. Plug the display cable into your card; then turn on the computer and monitor. To connect a D-Sub monitor to your graphics card, use the D-Sub connector. To connect a flat panel display to your graphics card, use the DVI-I connector. To connect an HDMI monitor to your graphics card, use the HDMI connector. Connect an HDMI monitor To HDMI Monitor To D-Sub Monitor To Flat Panel Display Connect a D-Sub monitor Connect a flat panel display You are now ready to proceed with the installation of the graphics card driver. Please refer to next chapter for detailed instructions. -9 -Hardware Installation How to enable the ATI CrossFireXTM technology? Step 1: Install two CrossFireX graphics cards of the same chipset on a CrossFireX-supported motherboard and connect the graphics cards via two CrossFire bridge interconnect cables (Figure 1). Then users can enable the CrossFireX technology through the graphics card driver. Two CrossFire bridge interconnect cables. Two CrossFire graphics cards of the same type. (Example: GV-RX195P256D-RH) Figure 1 Step 2: After installing graphics card driver in operating system, when an ATI CrossFireX configuration is detected for the first time by the ATI Catalyst display driver, ATI CrossFireX support is automatically enabled, and the best possible GPU combination is selected based on the hardware configuration. If ATI CrossFireX is not enabled, access the ATI Catalyst Control Center (please refer to Page 14). From the ATI Catalyst Control Center, enter the CrossFireX menu and assure to select the Enable CrossFireXTM check box (Figure 2). Figure 2 GV-R4600 Series Graphics Accelerator - 10 3. Software Installation Notice the following guidelines before installing the drivers: 1. First make sure your system has installed DirectX 9 or later version. 2. Make sure your system has installed the appropriate motherboard drivers (for the motherboard drivers, please contact the motherboard manufacturer.) 3.1. Driver and Utility Installation 3.1.1. Driver Installation After installing the operating system, insert the driver disk into your optical drive. The driver Autorun screen is automatically displayed which looks like that shown in the screen shot below. (If the driver Autorun screen does not appear automatically, go to My Computer, double-click the optical drive and execute the setup.exe program.) Step 2: Select the displayed language and then click Next. Step 1: Click the Install Display Driver item. Step 3: Click the Install button. For software MPEG support in Windows XP, you must install DirectX first. Users who run Windows XP with Service Pack 2 or above do not need to install DirectX separately. - 11 - Software Installation Step 5: Click the Accept button. Step 5: Click the Accept button. Setp 4: Click the Express or Custom icon and then click Next. The system is installing the components. Step 6: Click the Finish button to restart the computer. Then the driver installation is completed. GV-R4600 Series Graphics Accelerator - 12 3.1.2. GIGABYTE Gamer HUD Lite on Driver Disk Step 1: Click the GIGABYTE Gamer HUD Lite item. Step 2: Choose the language for the installation and click the OK button. Step 3: Click the Next button. Step 4: Click the Install button. The system is installing the components. Step 5: Click the Finish button. Then the installation ofthe GIGABYTE Gamer HUD Lite is completed. - 13 -Software Installation GIGABYTE Gamer HUD Lite The GIGABYTE Gamer HUD Lite allows you to adjust the the working frequency of the GPU and video memory. Help page Displays the current operating frequency Hardware Automatically Monitor optimizes the frequency Enables manual adjustment Clock adjustment(Note) of the frequency Button Function Default (Note) Allows you to load the default settings Apply(Note) Allows you to save the values you adjust Enable Lets the utility optimize the GPU/memory frequency settings Disable Allows you to manua...