Assessments - 3, GPA: 3.7 ( )

Fabricante : Sony Arquivo Tamanho: 341.56 kb Arquivo Nome : Língua de Ensino:

OTHERS To prepare the Synchronised recording SYNCHRO REC TAPE SPEED 1 Set the timer on the equipment to the time of the programme you want to record, then turn the equipment off. 2 Insert a tape with its safety tab in place. Make sure the tape is longer than the total recording time. 3 Set TAPE SPEED to select the tape speed (SP or LP for the PAL colour system, and SP or EP for the NTSC colour system). 4 Hold SYNCHRO REC down for more than two seconds. The SYNCHRO REC button lights up and the unit stands by for recording. The unit automatically turns on and starts recording when it receives audio/video signals from the connected equipment. To cancel the Synchronised recording Press SYNCHRO REC so that the button’s light turns off. To stop recording Press x STOP while recording. The unit automatically stops recording when the tape reaches the end or when the other equipment stops transmitting the audio/video signals. Notes • Some TVs or other equipment automatically turn off in a certain time if you do not operate it after it turns on with the timer. In this case the Synchronised Recording also stops automatically. • The Synchronised Recording starts and stops according to the signals from the connected equipment. Refer also to the instruction manual of the connected equipment for its timer function. • Some equipment keeps transmitting signals even though the power is off. In this case, the Synchronised Recording feature does not work because the unit will not be able to know when to start recording. Additional Information • If the unit is brought directly from a cold to a Warning Troubleshooting warm location, moisture may condense inside the unit and cause damage to the video head and tape. When you first install the unit, or To prevent fire or shock hazard, do not expose the If you have any questions or problems not covered below, please consult your nearest Sony when you move it from a cold to a warm unit to rain or moisture. service facility. location, wait for about one hour before To avoid electrical shock, do not open the cabinet. operating the unit. Refer servicing to qualified personnel only. Symptom Remedy The mains lead must only be changed at a Caution The ?/1 ON/STANDBY switch does • Connect the mains lead securely. qualified service shop. Television programmes, films, video tapes, and not function. other materials may be copyrighted. Unauthorized The power is turned on but the • Moisture condensation has occured. Turn the power recording of such material may be contrary to the unit does not operate. off, unplug the mains lead and leave the unit to dry Precautions provisions of the copyright laws. Also, use of this for over an hour. recorder with cable television transmission may Safety require authorization from the cable television The unit enters standby mode • The auto safety system is triggered to protect your • This unit operates on 110 – 240 V AC, transmitter and/or programme owner. 50/60 Hz. Check that the unit’s operating voltage is identical with your local power Compatible colour systems Playback Recording* Others Power supply. • Check the colour systems of your unit using • If anything falls into the cabinet, unplug the unit and have it checked by qualified the table below. pressing ?/1 ON/STANDBY again, disconnect the personnel before operating it any further. • The unit is not disconnected from the mains as Colour system seconds. Then reconnect the mains, and press Model name long as it is connected to the mains, even if the ?/1 ON/STANDBY again. If the unit still does not Recording Playback unit itself has been turned off. PAL PAL SLV-GA55ME/ • Unplug the unit from the mains if you do not MES/PS/SG/TH MESECAM MESECAM intend to use it for an extended period of time. NTSC 4.43 NTSC 4.43 SLV-GA65MJ To disconnect the cord, pull it out by the plug, NTSC 3.58 NTSC 3.58 never by the cord. PAL The picture is not clear. • Adjust the tracking with the V/v NORMAL/SLOW/ SLV-GA35ME/ STILL ADJUST buttons. MESECAM PS/SG/TH Installing NTSC 4.43 • Make sure the COLOR SYSTEM switch is set to the • Allow adequate air circulation to prevent internal heat buildup. • Do not place the unit on surfaces (rugs, Recording of video sources based on other blankets, etc.) or near materials...

Baixe o seu

Para fazer o download, introduza 2 dígitos :