Assessments - 2, GPA: 5 ( )

Fabricante : Sony Arquivo Tamanho: 275.31 kb Arquivo Nome : Língua de Ensino:

Check your model number by looking at the rear panel of your unit. The SLV-XA137PS is the model used for illustration purposes. Any difference in operation is clearly indicated in the text, for example, "SLV-XA127PS only." 4 Getting Started Step 2 Setting up the remote commander Inserting the batteries Insert two R6 (size AA) batteries by matching the + and - on the batteries to the diagram inside the battery compartment. Using the remote commander You can use this remote commander to operate the unit and a Sony TV. To operate this unit, point at the remote sensor on the unit. To operate the TV, point at the remote sensor on the TV. Remote sensor TV/VIDEO ; (TV power) u (on/standby) PROG(CH) +/- VOL +/- To Press Turn the TV to standby or active mode u (on/standby) Turn on the TV power ; (TV power) Increase (+) or decrease (-) the TV volume VOL +/- Change the TV programme position PROG(CH) +/- Select an input source on the TV either aerial in or line in TV/VIDEO Notes • With normal use, the batteries should last about three to six months. • If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage. • Do not use a new battery with an old one. • Do not mix different types of batteries. Getting Started 5 Getting Started Step 3 Connecting the unit 1 Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the unit. AERIAL OUT 2 Connect AERIAL OUT of the unit and the aerial input of your TV using the supplied aerial cable. AERIAL OUT 3 Connect the mains lead to the mains. IN IN 6 Getting Started Additional connections To a TV that has phono type audio/video input jacks This additional connection improves picture and sound quality. Connect the TV as shown on the right. If you want to use the Trinitron TV Synchro Play function (see page 12), this connection is necessary. (If your TV has two or more inputs, connect the audio/video cable to the VIDEO IN 1 jacks.) For SLV-XA17PS/XA127PS This unit Audio/video cable (not supplied) For SLV-XA37PS/XA137PS This unit Audio/video cable (not supplied) Getting Started 7 Getting Started Step 4 Tuning your TV to the unit If you have connected your unit to the TV using the audio/video cable, skip this step. ON/STANDBY -\ □ a H H 1 ON/STANDBY Press ON/STANDBY to turn on the unit. 2 Turn on your TV and select a programme position for video playback. Choose a channel between UHF 30 and 39 on the TV where there is no picture and no sound or only a steady rustling sound. This channel will now be referred to as the video channel. 3 Insert a tape recorded in the colour system matching your TV into the cassette compartment. (SLV-XA17PS/XA127PS) The unit starts on, and starts playing automatically. (SLV-XA37PS/XA137PS) The unit starts on, and starts playing automatically if you insert a tape with its safety tab removed. 4 Press £ PLAY on the unit. 5 Tune the TV until the video playback picture is clearly displayed on the TV screen. Refer to your TV manual for tuning instructions. You have now tuned your TV to the unit. From now on, whenever you want to play a tape, set the TV to the video channel. If the playback picture does not appear clearly, see "To obtain a clear playback picture" on page 9. 8 Getting Started jp /-« 0 t' _ ®s Q ®® To obtain a clear playback picture If the playback picture does not appear clearly in step 5 above, turn the RF CHANNEL screw on the rear panel of the unit with a rf CHANNEL screwdriver to a position where the TV clearly displays the playback picture. To select the TV system For your TV to receive the correct signal from your unit, you must set the TV SYSTEM switch on the rear panel of the unit to either G (for system B/G) or K (for system D/K). If this switch is set to the wrong position, the sound will be distorted. Getting Started 9 Getting Started Basic Operations Playing a tape S' a 1 1 Г 1 1 —1 ~ 1 NTSC PB COLOR SYSTEM 6 EJECT 3/# SEARCH P PAUSE ) FF £ PLAY p STOP 0 REW 1 Turn on your TV and set it to the video channel. 2 з Insert a tape. (SLV-XA17PS/XA127PS) The unit turns on, and starts playing automatically. (SLV-XA37PS/XA137PS) The unit turns on, and starts playing automatically if you insert a tape with its safety tab removed. Press £ PLAY. When the tape reaches the end, it will rewind automatically. 10 Basic Operations Additional tasks To Press Stop play p STOP Pause play P PAUSE Resume play after pause P PAUSE or £ PLAY Search forward ) FF or # SEARCH during playback Search backward 0 REW or 3 SEARCH during playback Fast-forward the tape ) FF during stop Rewind the tape 0 REW during stop Eject the tape 6 EJECT To set the colour system If streaks appear during playback, set COLOR SYSTEM on the unit to conform to the system that the tape was recorded in. (Normally set the switch to AUTO.) If your tape was...

Baixe o seu

Para fazer o download, introduza 2 dígitos :