Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Unauthorized recording of such material may be contrary to the provisions of the copyright laws. Also, use of this recorder with cable television transmission may require authorization from the cable television transmitter and/or programme owner. Compatible colour systems • This unit is designed to record and play back using the PAL (B/G and D/K), MESECAM (B/G and D/K), NTSC 3.58, and NTSC 4.43 colour systems. Recording of video sources based on other colour systems cannot be guaranteed. • Tapes recorded with the NTSC colour system can be played back on this unit using a TV or a colour monitor for the PAL colour system. • To play back tapes recorded with the PAL and MESECAM colour systems, you need a TV or colour monitor compatible with these systems. Introduction Table of contents Getting Started 4 Step 1: Unpacking 5 Step 2: Setting up the remote commander 6 Step 3: Connecting the unit 8 Step 4: Tuning your TV to the unit 10 Basic Operations Playing a tape 14 16 17 Additional Operations Playing/searching at various speeds Adjusting the picture Editing with another VCR Additional Information 19 21 22 Troubleshooting Specifications Index to parts and controls back cover Index Getting Introduction 3 Getting Started Step 1 Unpacking Check that you have received the following items with the unit: • Remote commander • Aerial cable • Audio/video cable (3-phono to 3phono) (SLV-XF247PS only) • R6 (Size AA) batteries Checking your model name The instructions in this manual are for the 2 models: SLV-XA147PS and XF247PS. Check your model number by looking at the rear panel of your unit. The SLV-XF247PS is the model used for illustration purposes. Any difference in operation is clearly indicated in the text, for example, “SLV-XA147PS only.” Getting Started Step 2 Step 2 Setting up the remote commander Inserting the batteries Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment. Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position. Getting Using the remote commander REC Remote sensor You can use this remote commander to operate the unit and a Sony TV. To operate this unit, point at the remote sensor on the unit. To operate the TV, point at the remote sensor on the TV. TV/VIDEO ;(TV power) u (on/standby) PROG (CH) +/– VOL +/– To Press Turn the TV to standby or active mode u(on/standby) Turn on the TV power ;(TV power) Increase (+) or decrease (–) the TV volume VOL +/– Change the TV programme position PROG (CH) +/– Select an input source of the TV either from aerial in or from line in TV/VIDEO Notes • With normal use, the batteries should last about three to six months. • If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage. • Do not use a new battery with an old one. • Do not mix different types of batteries. 5 Getting Started Step 3 Step 3 Connecting the unit to mains : Signal flow AERIAL IN AERIAL OUT Aerial cable (supplied) 1 Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the unit. AERIAL OUT IN 2 AERIAL Connect AERIAL OUT of the unit and OUT the aerial input of your TV using the supplied aerial cable. IN 3 Connect the mains lead to the mains. Getting Started Additional connections (A/V connection) To a TV that has phono type audio/video input jacks This additional connection improves picture and sound quality. Connect the TV as shown on the right. If you want to use the Trinitron TV Synchro Play function (see page 13), this connection is necessary. (If your TV has two or more inputs, connect the audio/video cable to the VIDEO IN 1 jacks.) To a stereo system (SLV-XF247PS only) You can improve sound quality by connecting a stereo system as shown on the right. For SLV-XA147PS This unit TV AUDIO VIDEO LINE IN LINE OUT Audio/video cable (not supplied) For SLV-XF247PS This unit TV Audio/video cable (supplied) AUDIO VIDEO LINE 1 IN LINE 1 OUT This unit Stereo system AUDIO VIDEO LINE 1 IN LINE 1 OUT Audio cable (not supplied) IN VIDEO AUDIO Getting IN VIDEO AUDIO AUX IN 7 Getting Started Step 4 Step 4 Tuning your TV to the unit If you have connected your unit to the TV using the audio/video cable, skip this step. ON/STANDBY REC 1 ON/STANDBY Press ON/STANDBY to turn on the unit. 2 Turn on your TV and select a programme position for video playback. Choose a channel between UHF 30 and 39 on the TV where there is no picture and no sound or only a steady rustling sound. This channel will now be referred to as the video channel. 3 Insert a tape recorded in the colour system matching your TV into the cassette compartment. The unit starts playing automatically if you insert a tape with its safety tab removed. 4 Press a PLAY on the unit. 5 Tune the TV until the video playback picture is clearly displayed on the TV screen. Refer to your TV manual for tuning instructions. You have now tuned ...
Este manual também é adequado para os modelos :VCR jogadores / vídeo - SLV-XA147PS (399.87 kb)