Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
2. Select one option between Enable and Disable using the or OK button. GB 63 10. Installation 10.3 Default Setting Default Setting restores the product to the default settings. Warning: Please note that once you perform Default Setting, all data such as Channel List and User Configured data are deleted, no information on the HDD will be lost. To perform Factory Default: 1. Press the MENU button. 2. Select Installation using the button and press the OK 3. Enter Password using the NUMERICAL (0-9) button. 4. Select Default Setting using the button, press the OK or or button. button. 5. Select Yes and press the OK button to restore all setting to Factory Default. Select No and press the OK or BACK button to return to the previous menu. 6. Confirm again to start loading default setting. Enter Password using the NUMERICAL (0-9) button to perform restoring. 7. When completing the default setting, press the OK button to automatically run the Installation Wizard. For detailed information about Installation Wizard, refer to 3. Installation Wizard. Note: The default password is 0000. GB 64 10.4 Antenna Power When you connect an active antenna to the ANTENNA IN connector on the rear of the product. 1. Press MENU button. 2. Select Installation using the button and press the OK or button. 3. Select Antenna Power from Installation menu using the button. 4. Press the OK or button to select On or Off . On 5V power supply from the active antenna cable. Off No power supply. Note: • Active antenna is the portable or indoor antenna which needs power supply from the set top box bacuse it does not have power cord for itself. • The default value is Off. GB 65 11. Software Update In order to maintain proper performance of the product, it is essential to have the most up to date software. The latest news and release of software versions may be found at Humax website -It is recommended that you periodically check for the availability of software upgrade. 11.1 OTA (Over the Air) OTA, an abbreviation of "over the air", means downloading the software where the manufacturer reserves the right to decide when and where to release through aerial. Over the Air(OTA) is simply another alternative for downloading software versions. However, the manufacturer reserves the right to decide when and where this software update can take place by "beaming" latest software versions over the air via aerial. The software update via aerial will only occur under the following circumstances. 1. The equipment should have appropriate loader software. Caution: Please note that if you don't have normal loader software, the equipment may not be updated or work after software update. 2. The manufacturer decides to release software downloading via a designated aerial. 3. The equipment must be "tuned" properly to the same aerial that the manufacturer uses. 4. Update software when the quality of receiving signal strength is high. if the quality of receiving signal strength is not recommendable due to bad weather, upgrade the software later. Caution: • Please be careful to keep the power on and the power cord plugged in during software update. If the power is off during software update, it may cause fatal damage to the product. • Please be careful not to pull out the Signal line (co-axial Cable) during software update. Update may be interrupted and the product may not work. Note: • The product cannot work at all during software update. • It may take 5 ~10 minutes to update software. • Scheduling operation cannot work during software update. 1.Ifnewsoftwareisfoundwhenpoweringon 1. A message will be displayed to notify that new software is found. 2. Select Yes and press the OK button to update the software. 3. Starts downloading new software. Please wait until the update is completed. 4. When completing the software update, the equipment is automatically powered off and on again. GB 66 2.IfupdatingsoftwarefromMenu 1. Press the MENU button. 2. Select Installation using the button and press the OK or button. 3. Enter Password using the NUMERICAL (0-9) buttons. 4. Select Software Update using the button and press the OK or button. 3.Ifnewversionofsoftwareisdetectedduringwatchingaprogramme Press the OK button to start updating 4.IfusingAutomaticUpdate You can set the product to find HUMAX software update site and update software automatically. 1. Select Automatic Update from Software Update screen using the button and press the OK or button. 2. Automatically search for new software. Select Cancel and press the OK button to finish Search. 3. When detecting update software, the following result is displayed. If new software is not found by Automatic update, use Manual Update. 4. Select Yes and press the OK button to start updating. Select No and press the OK button to return to the previous menu without updating. 5. When completing the software update, the product is automatically powered off and on again. GB 67 11. Software Update 5.ManualUpdate...