To enable this function, both AUTO PLAY mode and AUTO RTN mode should be turned on, and the AUTO RTN START point and the AUTO RTN END point should already be set. Using this function will facilitate the Auto Punch In/Out and Manual Punch In/Out rehearsal. See “Hint” after the following section. If the "Chain Play mode" in the SETUP mode is set other than "Off," ON/OFF of AUTO REPEAT cannot be executed. 2. Press the [AUTO RTN/AUTO PLAY] key to turn on the [PLAY RTN], [AUTO PLAY] LEDs. AUTO RTN END point AUTO RTN START point LOCATE PLAYBACK START PLAYBACK 3. Start playback a little before the AUTO RTN START point. The recorder operates as shown in the diagram, and stops at the AUTO RTN START point. • You can set a preroll time in the “Preroll Time?” menu in SETUP mode so that the recorder will start playback preroll time before the locate point. You can set the preroll time from 0 to 10 seconds. Refer to the chapter “Changing the Initial Settings (SETUP Mode)” on page 1. Store the AUTO RTN START and AUTO RTN END “112.” points. Refer to the chapter “Storing a Locate Point (Edit Point)” on page “ 50” for information on storing the desired points in the [AUTO RTN START] key and the [AUTO RTN END] key. You can make repeated Auto Punch In/Out rehearsal much easier and quicker by using the Auto Repeat function. Set the AUTO RTN START point prior to the AUTO PUNCH IN point, and set the AUTO RTN END point after the AUTO PUNCH OUT point. The recorder will repeat the operation automatically so you can concentrate on your rehearsal. Cancel Auto Repeat mode before you record a take. The recorder will play this range repeatedly for rehearsal, which makes it easy for you to check the recording level and practice your performance. AUTO PUNCH IN point AUTO PUNCH OUT point AUTO RTN END point AUTO RTN START point PLAYBACK START Rehearsal range PLAYBACK LOCATE 56 Model D2424 Reference Manual (Chain Play function) Chain Play function “Chain play” functions to playback, in any order, the tunes recorded on a multiple number of programs. There are three modes of chain play and each operates as shown below. Before executing these modes, “AUTO RTN START point” and “AUTO RTN END point” must be set for each program. For details, please read the explanations starting from the next page. In the pause mode, as shown in the example on the left, upon reaching the “END point” at playback of program 02, the recorder automatically stops at the “START point” of program 05 which is to be played back next. If chain play is executed again at the stopped point, it will stop again at the next program 10 “START point.” AUTO RTN START point Playback Playback Playback AUTO RTN START point AUTO RTN START point AUTO RTN END point AUTO RTN END point AUTO RTN END point PGM 02 PGM 05 PGM 01 STOP STOP STOP AUTO RTN START point AUTO RTN END point STOP PGM 02 AUTO RTN START point AUTO RTN END point PGM 05 AUTO RTN START point AUTO RTN END point PGM 01 Playback Playback Playback In the auto play mode, as shown in the example on the left, upon reaching the “END point” of program 02 started in playback, the recorder will automatically playback in setup order between the “START points - END points,” and, at the moment playback is finished at the “END point” of the last program 01, stops at the “START point” of the first program. In the repeat mode, playback is repeated until the above auto play mode is canceled. If power is switched off and then switched on again while set to the Repeat mode, playback will automatically start from the first program. AUTO RTN START point Playback Playback Playback AUTO RTN START point AUTO RTN START point AUTO RTN END point AUTO RTN END point AUTO RTN END point PGM 02 PGM 05 PGM 01 57 Model D2424 Reference Manual (Chain Play function) Setup of the Chain Play List The chain play list is setup via the “Chain Play List?” menu in the SETUP mode. The following procedure is based on the assumption that a multiple number of programs are in the current drive and that a tune is recorded in each program. 1. Enter the SETUP mode by pressing the [SETUP] key while the D2424 is in the stop mode. 2. Use the [JOG] dial to display the “Chain Play List?,” and then press the [EXECUTE/YES] key. The display will change to setup of the play list. Flashing ° 42 OL 0 30 24 18 12 9 6 3 kHz 24 FS BIT SETUP 24 ° 42 OL 0 30 24 18 12 9 6 3 2322212019181716151413121110987654321 CLOCK INT ° 42 OL 0 30 24 18 12 9 6 3 kHz 24 FS BIT SETUP 24 ° 42 OL 0 30 24 18 12 9 6 3 2322212019181716151413121110987654321 CLOCK INT This display indicates the initial setting in which no chain list is setup (“EE” means “invalid.”). The chain play number can be set in the currently blinking section (left) and numbers “01” through “99” can be input via the [JOG] dial. Also, the flashing section can be moved from the left “01” to the right “EE” by pressing the [EXECUTE/ YES] key, and e...
)
