Therefore, to execute the multitrack recording using the D2424LVmkII, you have to separately prepare a current drive. For a current drive, you can use any universal "E-IDE" hard disk drive* which has been tested and approved by FOSTEX. A hard disk drive can be installed in the removable case attached. The updated information on the operation-confirmed HD and backup media for D2424LVmkII is mentioned in the following Fostex international web site. Be sure to turn off the power to the D2424LVmkII (or remove the power cable from the AC outlet) before installing a hard disk. First, you need to disassemble the caddy included in the package so that you can install a hard disk into it. Installing a hard disk in the caddy • Disassembling the caddy 1. Apply your thumb to the edge of the case on the connector side as shown in the figure, and slightly pull the cover in the direction of the arrow. 2. Apply your thumbs to the side of the case and open the cover. In the same manner, open the cover on the other side. (Caution: Be careful not to pinch your fingers.) • A hard disk is a high-precision device. Do not apply any impact to the disk when and after you install it in the caddy. Do not leave the disk near a device that generates a strong magnetic field. Choose a level and stable surface for installation. Be careful not to injure yourself. Fostex is not liable for any malfunction or damage to the hard disk caused by mishandling. • You need to set the DIP (Jumper) switch on the hard disk to “Master” before you install it into the caddy. If the switch is set to “Slave,” the hard disk will not function correctly. Refer to the instruction manual that came with your hard disk for more information on the DIP (Jumper) switch setting. Model D2424LVmkII Quick Operation Guide • Connecting cables 1. Connect the cables in the caddy to the connectors on the rear of the hard disk. As shown in the figure, first connect the power supply cable. Make sure that you connect the cables securely in the correct direction. Some connectors on the hard disks may be too tight to connect cables easily. Do not apply excessive force to such connectors to avoid injury or damage to the hard disk. • Fixing the hard disk to the case 1. Align the screw holes. As shown in the figure, align the screw holes on the side of the disk with the holes on the case. 2. Insert four included fixing screws (two screws on each side) and tighten them. Tighten four screws (two on each side). Align the screw holes on the other side of the hard disk with the holes on the case. Do not tighten the screws too much. Otherwise, you may damage the case. • Assembling the case When you assemble the case, follow the note below: If a projecting part on the hard disk touches the cover, apply the insulation seal (included in the package) to the surface of the case where the part would touch. If you use the disk with its part touching the cover, a short-circuit may occur, leading to a malfunction. 1. Assemble the case by installing the covers. After you assemble the case, store the case in a place not subject to magnetic fields. If you remove the case from the recorder and store or move the unit, cover the connectors on the caddy with the dust cover (included in the package) to protect the hard disk from building up static electricity and dust. Do not touch the connectors with your fingers to avoid static electricity. 7 Model D2424LVmkII Quick Operation Guide • Installing the removable case in the recorder 1. Install the caddy (containing a hard disk inside) into the slot. Push in the case with the correct side facing toward you. (Use both hands to push it in so that the surface of the case and the front panel become flush.) 2. Use the coin to lock the caddy. Caddy Coin etc. Do not forget to lock the caddy installed into the slot. When locking or unlocking the caddy with the coin, make sure that the recorder's power is off. • Connecting a detachable controller 1. Attach a detachable controller (included) to the hooks on the front panel. 2. Securely insert the controller’s connector cable to the connector on the front panel. Instead of using the controller, you may use an optional extension cable (Model 8551B). Consult your dealer for more...
