If the Vari-pitch function was on, the unit will use the pitch data previously set. The Vari-pitch function will be automatically turned off in the following situations: * When you turn on the power to the unit (The pitch data will be reset to 0.0%.) * When you set Slave mode ON. (The pitch data remembers the previous setting.) * When you set up the digital input tracks and “DIGITAL” appears on the display. (The pitch data remembers the previous setting.) If you have installed an optional Model 8345 TC/SYNC card in the D-160 and you have set the “Word Out?” menu in the Setup mode to “8345,” the Vari-pitch function turns on even during digital input via DIGITAL IN. * Refer to page "56" for more information on the Vari-pitch function. * Refer to page "123" for more information on Slave mode. * Refer to page "60" for more information on digital signals. 19 D-160 Owner's Manual (Names and Functions) 29. Paste key [PASTE] Press this key to copy data or move data that has been copied to the clipboard to a location stored at the AUTO PUNCH IN key. The data will be pasted at the point stored in the Auto Punch In key. You can select the paste destination track using the RECORD TRACK select key. A destination track to which data is pasted is identical to the source track. This key is activated only when the recorder transport section is stopped. * Refer to page "85" for more information about the Copy & Paste, and Move & Paste operation. 30. Move key [MOVE] This key is used to enter into the clipboard data stored in memory by the CLIPBOARD IN/ OUT keys. Pressing the MOVE key will store the data in the Clipboard as Move data. To enter data to be moved, one or more tracks must be readied, and a correct value must be stored for the In and Out points. If you attempt to enter data when all tracks are safe, all track indications and "Select Track!" indication on the display will blink to warn you. If a correct value is not set for the Clipboard In or Out points, a warning message of “Void In Point!” or “Void Out Point!” will appear. * Refer to page "85" for more information about the Copy & Paste, and Move & Paste operation. 31. Copy key [COPY] This key is used to copy data stored in the memory using the CLIPBOARD IN/OUT keys. Pressing the COPY key will store the data in the Clipboard as Copy data. To execute the copy operation, one or more tracks must be readied, and a correct value must be stored for the In and Out points. If you attempt to copy data when all tracks are safe, all track indications and a "Select Track!" indication on the display will blink to warn you. Ifacorrect value is not set for the Clipboard In or Out points, a warning message of “Void In Point!” or “Void Out Point!” will appear. * Refer to page "85" for more information about copying data. 32. Auto Punch Mode On/Off key [AUTO PUNCH] Switch this key ON for auto punch in/out. When you press this key while a correct value is stored to the AUTO PUNCH IN key and the AUTO PUNCH OUT key, both the REHEARSAL LED and TAKE LED will blink, indicating that Auto Punch mode is on. (If a correct value is not stored, pressing the AUTO PUNCH key will not turn the parameter ON, and the message “Void Out Point!” will appear.) Pressing the PLAY button under this condition will put the unit into "Rehearsal mode" for Auto Punch In/Out recording. Pressing the PLAY button and RECORD button simultaneously will put the unit into "Take mode." There are five combinations of the REHEARSAL LED and TAKE LED that indicate the status of the unit regarding auto punch recording: If a correct value is not stored, pressing the AUTO PUNCH key will not enable the function, and the message “Void Out Point!” will appear. If a correct value is not stored, pressing the AUTO PUNCH key will not turn on the function, and the message “Void Out Point” will alert you. In this case, set a correct value for the Auto Punch In/Out point. Also, the function is not turned on when you press the AUTO PUNCH key if the disk does not have enough recording space. The display will indicate “-**h**m**s**f Over.” Auto Punch mode OFF Both REHEARSAL LED and TAKE LED are off. Auto Punch mode ON Both REHEARSAL LED and TAKE LED are blinking. Auto Punch Take mode Only the TAKE LED (red) is lit. Auto Punch Rehearsal mode Only the REHEARSAL LED (green) is lit. Rehearsal mode entered by means of MMC or foot switch Only the REHEARSAL LED (green) is blinking. * Refer to page "75" for more information about the Punch In/Out. 20 D-160 Owner's Manual (Names and Functions) Auto Punch In/Out mode Punch In/Out mode Rehearsal Take Rehearsal Take Punch In/Out mode and LED display Manual Punch In/Out using a footswitch or MMC. (Auto Punch mode OFF.) :go off :light up :blink AUTO TAKE REHEARSALPUNCH AUTO TAKE REHEARSALPUNCH AUTO TAKE REHEARSALPUNCH AUTO TAKE REHEARSALPUNCH AUTO TAKE REHEARSALPUNCH AUTO TAKE REHEARSALPUNCH 33. Locate key [LOCATE] Press this key to locate a position. You can locate a point (memory data) ...
Log: