Assessments - 3, GPA: 3.7 ( )

Fabricante : EverFocus Arquivo Tamanho: 3.23 mb Arquivo Nome : Língua de Ensino:

(This can be done while DVR is powered on) The rear USB V1.0 port is recommended to reserve the higher speed front USB V2.0 port for video copy/export. NOTE: Recommended mouse types are Logitech® and Microsoft® wired USB wheel-mouse. Wireless USB mouse is not supported. 1.11NETWORK CONNECTION This section only describes physical connection to an Ethernet network. This step must be completed before the DVR can connect to the network. There are two basic types of connection: 1.11.1 Direct PC Connection through Crossover Network Cable The point-to-point connection of DVR and PC requires a crossover (crossed) network cable. This type of connection is ONLY used for direct connection to a single PC. Make sure that the PC is equipped with a 10/100/1000 Mbps compatible network connection. Figure 1-3 Direct PC Connection Pinout of crossover-cable 11 1.11.2 Network Connection through Patch Cable The connection to an existing network requires a normal patch cable (straight-through). The illustration shows the connection to a network switch or router. Figure 1-4 Network Connection through Patch Cable Pinout of straight patch cable 1.12FINAL INSTALL PROCESS Once you have completed the basic wiring connections, you are ready to turn on the DVR. Simply plug in the power source. The POWER LED will light up if power is normal. Once the system has finished loading, you can begin to set up the menu options for the DVR. 12 Chapter 3 2 MOUSE AND FRONT PANEL OPERATION ECOR264-4/ECOR264-8 DVRs support multiple sources to control the DVR. It can be controlled with a mouse, the front panel, an EKB500, and the handheld remote control. This chapter will cover the basic operation using the mouse and the front panel buttons. 2.1 GENERAL USB MOUSE OPERATION 2.1.1 How to select a channel / Enable audio 1. In a view consisting of more than one channel, users can select a channel by clicking once on the desired channel screen. The selected screen will be highlighted by a white frame. 2. Double clicking on a channel screen will display full screen for this channel. 3. To enable audio out, click the audio icon (ex: ) at lower side of the screen. This system has only one audio out. Click this button to enable or disable the audio-out mode. 2.1.2 OSD Root Menu 1. Right-click the mouse to obtain the DVR control bar (see Figure 2-1 OSD Root Menu ). When you move the mouse over each icon, its title will be displayed at the top of the control bar. Figure 2-1 OSD Root Menu 2. Click on any icon to perform that action. These actions are covered in detail in Chapter 3. 3. Click the “X” in the top-right corner to close the DVR control bar. 2.1.3 Operation in the Configuration Menus 13 14 Click on the icon to access the Configuration Menu. The Configuration menu screens (shown in Figure 2-2 OSD Menu) are divided into 3 main sections. Figure 2-2 OSD Menu 01 In section 1, there are ten setup options available. Move the mouse over an icon and click to select it. 02 In section 2, the categories for the selected icon will be displayed. Click on a choice to select it. 03 In section 3, all the options for the selected choice will be available. Click on a field to make changes. 2.1.4 Field Input Options The following are examples of different types of fields available in the Configuration menu. Textbox: Click on the box and an on-screen keyboard will appear*. (see note about the on-screen keyboard below) Dropdown box: Click on the down arrow to see all selections, then directly click on an option to select it. Check box: Click on the box to enable it (checked) or disable it (unchecked). Button: Click the button to execute the function. 01 03 02 Bar: Click and hold on the bar to adjust the set point Left or Right. * Note about on-screen keyboard: Click on a button to input that character. The buttons on the right and bottom have the following functions: Delete Delete the letter Done Confirm the selection All Caps Switch to capital letters Space Enter a space < Move to left > Move to right Cancel Cancel and exit from the keyboard . 15 2.2 General Front Panel Operation 2.2.1 How to select a channel / Enable audio 1. In a view consisting of more than one channel, use the mouse or press arrow keys (Up/Down/Right/Left) to scroll through each channel that is displayed. The selected channel will be highlighted by white frame. Pressing the “right” arrow when the last camera (4 or 8) is highlighted will select all cameras. 2. While channel #1 is selected, press the “Enter” button to turn Audio On/ Off. 2.2.2 OSD Root Menu 1. Press “Menu” key to display the DVR control bar. Use the left/right arrows to scroll over each icon. The title for each icon will be displayed on top of the control bar. 2. Press “Enter” key on any icon to perform that action. These actions are covered in detail in Chapter 3 3. Press “Menu” to close the DVR control bar. 2.2.3 Front Panel Key Review The basic principle of front panel operation is to use arrow keys to navigate among the menu items. Use...

Baixe o seu

Para fazer o download, introduza 2 dígitos :