|
Instruções de Operação Panasonic, Modelo WV7225
Fabricante : Panasonic
Arquivo Tamanho: 453.55 kb
Arquivo Nome : WV7225.PDF
Língua de Ensino: 
|
 
|
|
|
Ir para baixar
Facilidade de uso
Retighten the Cover Locking Screws and remove the Cover. • After mounting and wiring the pan/tilt head, replace the cover. • Engage on the Base Plate with the mounting groove in the Cover and tighten it with screws. 2. When mounting directly to flat ceiling: • Make four holes for mounting the pan/tile head. (Screws are not provided.) • Holes in the head are 5/8*(8mm). tL 3. When using the mounting bracket(WV-7030) * Use four hex head bolts, plain washers, lock washers and hex nuts (provided with the WV-7030) as shown below. • After wiring, replace the cover. 4, Mount the low voltage camera on the mounting plate.. Mount the TV Camera and lens to the mounting plate using with the camera mounting screw. u within 1-5/8’{5 cm) Caution: • Use the TV camera of AC 24V. • Mount the camera and lens at a center {within 1 -5/8*) of these length to the mounting plate. CAUTION: When carrying unit do not grasp by the case. Instead, support entire unit with hands when transporting. 5. Mount the indoor camera housing (WV-7110) on the Mounting Plate. • Remove the Camera Guide Pin to B position from A position. • Mount the camera housing using with the Camera Mounting Screw. 6. Mount the indoor Camera housing (WV-7120D) on the Mounting Plate. • Remove the Camera Guide Pin to C position from A position. • After mounting the camera housing with using the Camera Mounting Screw, mount the TV Camera on it. Camera Mounting Screw APPLICABLE CAMERAS, LENSES AND HOUSINGS O possible x impossible -5- TYPICAL SYSTEM CONNECTIONS System Controller WV-CU254 CONNECTION PRECAUTION: • Make all connections with the power turned OFF. • Avoid shorting the terminals, as this may blow a fuse. If the installation is to be upside-down, the Pan Left-right and Tilt Up-Down directions will be reversed. This must be considered when the wiring done. In this case, replace 1 and 2 pins of CN1 and CN2. If the pre-wired cable WV-CA51 is used, replace them as the above using with MOLEX bland tool 57031 -6000. • Wiring for Pan/Tilt and Motorized Zoom, Focus, Iris Control Control Voltage Control Current ZOOM TELE -6V DC WIDE +6V DC FOCUS NEAR -6V DC Less than 100 mA FAR +6V DC IRIS OPEN -6V DC CLOSE +6V DC When using a camera with motorized zoom, focus and iris, these connections should be made. Note: Lens control cable should be approx. sufficient room for Pan/Tilt 39’ to allow • Wiring of Coaxial Cable Wiring preparation: Prepare coaxial cables as shown as below. Foldback 10mm 3 mm 25 mm 1. Hold the shield wires 2. Connect the inner conductor 3. Clamp the shield wires (Under the embossed side) CAUTION: Use the following conditions cable. Impedance: 75ÎÎ Diameter: 8 mm or less Example: RG59/U (BELDEN9259) Coaxial cable -6- In case of using the connection (WV-CA51) The appearance of WV-CA51 is shown in the drawing. © No. Parts Name 1 17 wires cable 2 14P Housing 3 12P Housing 4 10P Housing 5 6P Housing 6 Contact 7 BNC Connector In case of using the accessory connectors (MX5557P0B) (MX5557P10) i i 10 9 8 7 6 5 4 3 2 1 3 2 1 CN-1 CN-2 WV-7225 side CN Pin No. WV-7225 Usage of Terminal Power Source CN2-1 LEFT CN2-2 RIGHT CN2-3 AUTO PAN 24V AC CN1-1 UP CN1-2 DOWN CN2-4 24V AC CAMERA CN2-5 AC COMMON 24V AC COMMON CN1-3 DC COMMON ±6V DC COMMON CN1-4 IRIS CN1-5 FOCUS ±6V DC CN1-6 ZOOM CN2-6 GND The approx. maximum cable length is the following wire gauge is shown in the chart. AWG size (UL1007 UL1015) Impedance (fl/km) Conductor #24 77.9 ft 32 m 10 #22 50.4 ft 49 m 15 #20 32.3 ft 78 m 24 #18 19.9 ft 139 m 40 How to assemble the connector 1. Strip back the cable jacket about 0.1 inches {3 mm) and separate the individual conductors. 2. Prepare the individual conductors for soldering or clamping. If clamping, use MOLEX brand tool part number 57027-5000 {for UL-Style cable UL1015) or 57026 - 5000 (for UL-Style Cable UL1007) Up Contact ^ • Wire \ n fl Insert the wire until A position l lj u u u 1 ancj clamp the contacts. After soldering or clamping the contacts push them into the proper holes in the connector housing until they snap in place. up | L -JTOT Contact In case of using WV-CU254, refer to it’s manuals. -7- End of Wiring 1. Turn on the End of wiring Power ON/OFF Switch of the TV camera. 2. Connect the power cord of the Indoor Receiver to a grounded electrical outlet, 24V AC. 3. Turn on the power ON/OFF Switch of the Indoor Receiver. Connection with TV Camera Camera Power Cable Connect the spade lug connectors to the 24V AC Power Terminal Strip of the lowvoltage camera, according to the diagram. Camera Cable Connect the Camera Cable to the video output connector of the lowvoltage camera. CAMERA Zoom Control Connector The control connector of the motorized zoom lens should be a 4-pin connector, Hirschman type Mas 4100. If it is not, substitute the existing connector with the Ma...
Escreva a sua própria avaliação do dispositivo
|
|
