Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
Setting the Jumpers and Switches MS8200 / MS8300 Installation Manual -Page 13 Remote Transmitters Using the Remote Transmitters Button 1 Button 2 Mode Button LED Each system comes with 2 Remote Transmitters, pre-programmed to Arm and Disarm the system withchirp confirmation using Button 1. The Mode Button will change function of both Button 1 and Button 2 each time it is pressed. When the Arm/Disarm Button is pressed together with any other Transmitter Button, the systems Chirp confirmation setting will be reversed. If the system was programmed to arm the system with chirp, Pressing Buttons 1 and 2 together will arm the system withoutchirp. If the system was programmed to arm the system withoutchirp, pressing Buttons 1 and 2 together will arm the system withchirp. Note also that the LED on the transmitter changes color each time the Mode Button is pressed to indicate the current function of Buttons 1 and 2. The LED will stay on for 5 seconds, then turn off, returning Buttons 1 and 2 to their off settings. The default setting of the Remote Transmitter is as pictured, where Button 1 is used to arm and disarm the system , Button 2 operates Auxiliary Function 1, Mode + 1 operates Auxiliary Function 2, etc. LED color none green orange red ARM Aux 1 Aux 2 Aux 3 Aux 4 not used not used not used MODE BUTTON Mode Button Sequence None:Green:Orange:Red:Green:... BUTTON 1 BUTTON 2 However, it is possible to set individual Remote Transmitters to arm and disarm the system using any of the Transmitters function Buttons, which is extremely useful when a Transmitter is used to control multiple system. See Adding a Remote Transmitter into the System. The Button Assignment of Arming and Disarming will not affect the operation of the Remote Page 14 -MS8200 / MS8300 Installation Manual during Programming, Logic Sensor II Adjustment, Space Shield III Adjustment, Real Time System Verification or any other system set-up function. The Buttons used to control those features will remain as they are described in this manual, regardless of how the Transmitter is set up to arm and disarm the system. Two Car Operation To use a single transmitter to operate multiple vehicles, the Transmitter can be set to arm Car #1 with Button 1 and arm Car #2 with the first available Button not being used by Car #1, which will be Mode, Mode, 1 if Car #1 is using Auxiliary functions 1 through 3. The Auxiliary functions for Car #2 will follow the arm/disarm button in sequential order. LED color none green orange red ARM Aux 1 Aux 2 Aux 3 ARM Aux 1 Aux 3 Aux 2 (A) (A) (A) (A) (B) (B) (B) (B) MODE BUTTON Mode Button Sequence None:Green:Orange:Red:Green:... BUTTON 1 BUTTON 2 A = Car 1 B = Car 2 As stated, the Programming and set-up functions of Car #2’s system will notbe affected by this Transmitter configuration and will operate exactly as described described in this manual. MS8200 / MS8300 Installation Manual -Page 15 Adding a New Transmitter into the System 1. Turn on the ignition. 2. Press and hold the Override switch. • The status LED will turn on red. 3. Within 5 seconds: Continue holding the Override switchand Press Transmitter Button 1* For remote arming withchirp confirmation. ---or --- Release the Override switchand Press Transmitter Button 1* For remote arming withoutchirp confirmation. • The status LED will flash once quickly to confirm that the new Remote Transmitter has been added. 4. Turn off the ignition. Deleting Transmitters (Adding a Remote Transmitter and Erasing All Other Remote Transmitters From the System) 1. Turn on the ignition. 2. Press and hold the Override switch. • The status LED will turn on red. Continue to hold the override switch. • After 5 seconds, the status LED will flash 4 times, then turn on red again. 3. Within 5 seconds: Continue holding the Override switchand Press Transmitter Button 1* For remote arming withchirp confirmation. ---or --- Release the Override switchand Press Transmitter Button 1* For remote arming withoutchirp confirmation. • The status LED will flash once quickly to confirm that the new Remote Transmitter has been added. 4. Turn off the ignition. * The Button that is pressed will be the Arm/Disarm Button on that Remote Transmitter. You may program any of the Transmitter’s buttons to arm and disarm the system at this point. Page 16 -MS8200 / MS8300 Installation Manual Programming System Initialization and Default Reset Following this procedure will set all System Programming Parameters to factory default settings. 1. Turn on ignition. 2. After 4 seconds, press and hold Buttons 1 and 2 together for 5 seconds. The siren will emit one long chirp, indicating that the reset signal was received. 3. Turn ignition off. • All System Programming parameters are now set to factory default settings. • The Arming Mode is set to Remote Arming only. • The Valet Mode is off. • The Logic Sensor II shock sensitivity is set to Level 6. • The Logic Sensor II motion sensitivity is set to Level 4. Arming Mode Selection (Pass...
Este manual também é adequado para os modelos :Vídeo - UNGO MS8200 (307.63 kb)