Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
(Regular setting) [See Note 1] COLOR: For color signal input only B/W: For black-and-white signal input only [See Note 2] □ Setting the HI-BAND recording mode Set the HI-BAND recording mode. ON: Recording proceeds in the high-resolution mode when black-and-white pictures are recorded. [See Note 4] OFF: The HI-BAND mode is set to OFF. hi-bano в/в on (VIDEO) MODE NMiES [Note 1] Power loss memory When power failures have occurred, the number of occurrences together with their dates and times are counted up to a maximum of 99 times, and the data of the 4 most recent occurrences is stored in the memory. [Note 2] Do not mix black-and-white and color signals when supplying them to the video input connectors. This will cause sync fluctuations and generate noise. [Note 3] When supplying signals which may cause the circuit to make an error in its automatic identification, set to COLOR for color signals and to B/W for black-and-white signals. When color signal are supplied with a B/W setting or black-and-white signals are supplied with a COLOR setting, unnatural video signals will be recorded. [Note 4] Set HI-BAND B/W to “ON” to play back pictures which were recorded at the HI-BAND B/W “ON” setting. If it is not set to “ON," noise may appear. These pictures cannot be played back properly on a VTR which is not equipped with the HI-BAND B/W facility. 45 C CAIARM/SENSOR RIO)) MODI OFF DURATION 0. IMIN IUIZER OFF REPEAT IN OFF (RESET PULSE) INPUT LEVEL HIGH (0AMIRA ЗШ TIMING 1F1 ELD MODE TM2 The alarm recording mode settings are performed on this screen. □ Selecting the alarm recording time mode Select the recording time mode when an alarm input is received. OFF: No alarm recording. 6H: 6-hour mode L18H: 18-hour mode (linear slow) L24H: 24-hour mode (linear slow) 24H: 24-hour mode (time lapse) NO CHANGE: The recording time remains unchanged even if there is an alarm input Tape start Alarm input i Tape end Recording Alarm recor- Recording ding mode - When there is an alarm input during recording in one of the time lapse modes, the recording time mode switches to the designated mode and the emergency scene is faithfully recorded. □ Setting the alarm recording duration Set how long the alarm recording is to last from the start to the end. 0.5MIN-6.0MIN: The time can be set to 0.5, 1.0, 1.5, 2.0, 3.0 and 6.0 minutes. CONTINUE: Alarm recording continues until the tape-end. MANUAL: Alarm recording is performed while the alarm input continues to be received. DURATION 46 [Displaying the screens] PROGRAM —1 OfF | TIME ' AOJ Set to “MENU.” Press one of these buttons until the desired menu screen appears. [Menu setting buttons] REV PLAY PLAY STOP PAUSE/STILL < I I l I □ I LPJ - PACE REW/® ®/FF REV ADV FWD ADV «11 W> I A V V SHIFT > SET +■ PAGE (-) button: Page down PAGE (+) button: Page up SHIFT (v) button: Move to Item below SHIFT (>) button: Move to item on the right SET (-) button: Change Item (decrement numerical value) SET (+) button: Change item (increment numerical value) □ Buzzer ON/OFF Set whether the buzzer is to sound during alarm recording. OFF: The buzzer does not sound. ON: The buzzer sounds while alarm recording is in progress. • Press any function button to release the buzzer. □ Setting the repeat-in function Set whether alarm recording is to proceed when there has been an alarm input while the tape was being rewound automatically in the recording mode. OFF: No alarm recording. ACCEPT: Alarm recording [See Note 1] □ Selecting the alarm reset pulse acceptance level Select the acceptance level of the alarm reset pulse. HIGH: The high level is set. LOW: The low level is set. (See page 68) □ Setting the timing Set the camera switchover timing signal which is to be output by the externa! sequential switcher during recording. The cameras are switched every 1-, 2-, 3-, 4-, 5-, 10-, 20-, 30- or 60-fields. [See Note 2] (CAUERA SD] Tim no [RESET PULSE] INPUT LEVEL REPEAT IN BUZZER NQifiES [Note 1] When “ACCEPT" is selected in the repeat-in function, be sure to set to other modes than “OFF" in step 1. If “ACCEPT" is selected when the repeat-in function is “OFF” in step 1, the unit may cause an error. [Note 2] When “TM1” has been selected as the camera switchover mode in step 7, the cameras are switched in frame units. Select “TM1” when the WJ-FS10A' frame switcher is connected and “TM2” when the WJ-FS616 frame switcher or any other sequential switcher is connected. (See page 77) [Note 3] The alarm recording mode in step 1 must be kept at a position other than “OFF” when “ACCEPT’ is to be selected by the repeat-in function. If “ACCEPT is selected while the mode is set to “OFF” the VTR may not operate properly. [Other notes] «The item settings are entered when the PROGRAM switch is returned to the "OFF” position. «When “MANUAL” is selected for the alarm recording duration, make sure to set the [TAPE END] MODE to ...