Assessments - 4, GPA: 4.8
(
)
)
|
Facilidade de uso
To prevent electric shock, do not remove screws or cover. There are no user-serviceable parts inside. Refer servicing to qualified service personnel. 2. Do not expose the camera to rain or moisture, and avoid operation in wet areas. Take immediate action if the camera should become wet. Turn the power off and request servicing from qualified service personnel. Moisture can damage the camera and create danger of electric shock. 3. Do not drop anything inside the camera. Dropping metal for example inside the camera could permanently damage the unit. If anything is dropped inside the camera, turn off the power immediately and refer to the qualified service personnel. Never aim the camera at bright objects, Whether the camera is in use or not, never aim it at the sun, or other extremely bright objects as this could cause blooming. Do not use the camera beyond its tempe.'a-ture, humidity or power source ratings. This camera is designed for indoor use. (a) The ambient temperature must not range beyond 14'F - 122‘F (-10'C -+50°C), (b) Avoid using the camera when the humidity is above 90%. (c) The input power source must be DC 12V, 190mA. MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS 1. 1/2” Manual Iris Lens (Sold Separately) 2. Mounting Holes There are two treaded holes (1/4") for mounting the camera onto the tripod and two or more threaded holes (No.832 UNC) for mounting the camera onto the mounting bracket. 3. Camera Connector (12-pin) This is connected with the optional Camera Cable GP-CA34 , GP-CA33, GP-CA59 or GP-CA60. -3- CAUTION: CONNECT THIS TO A DC 12V CLASS 2 POWER SUPPLY ONLY. Pin No. Description 1 Ground 2 + 12V IN* 3 Ground (or Video Out 4 Video Out 5 Ground for HD 6 HD In/Out 7 VD In/Out or frame reset in 8 Ground 9 No connection 10 Ground for Read out/inhibit 11 Read out/inhibit 12 Ground for VD 4. Switch 1 (1/ON) 1 I I I ON This switch is used to select the Field or Frame Accumulation. ON: Field Accumulation 1: Frame Accumulation Switch 2 (2/ON) 21 I ION This switch is used to select the Shutter Trigger A or B mode. A mode: Set this switch to the ON position. Set the Switch 1 to the ON position. Supply the frame reset signal into the pin-7 of the Camera Connector(3). The frame reset signal is latched by the internal HD signal. Set the Switch 3, Switch 4 and Switch 5 to the suitable position according to the following table. The 3 kinds of shutter speeds can be selected. Switch Shutter Speed (seconds) 5 4 3 ON OFF ON 1/2000 ON ON OFF 1/4000 ON ON ON 1/10000 Others Not specified B mode : Set this switch to the ON position. Set the Switch 1 to the 1 position. The shutter speed of approx. 1/2000 sec. is obtained regardless of Switch 3, Switch 4 or Switch 5 setting. 6. Switch 3 (3/ON) 3 I I I ON 7. Switch 4 (4/ON) 4l~ l~ION 8. Switch 5(5/ON) 5 I I I ON These switches {Switch 3, Switch 4 and Switch 5) are used to set the shutter speed as shown below. Switch Shutter Speed (seconds) 5 4 3 OFF OFF OFF NORMAL OFF OFF ON 1/125 OFF ON OFF 1/250 OFF ON ON 1/500 ON OFF OFF 1/1000 ON OFF ON 1/2000 ON ON OFF 1/4000 ON ON ON 1/10000 Note: The shutter speed does not function accurately under the non-interlaced synchronization. 9. Switch 6 (6/ON) 61 I ION This is the On/Off Switch for the Gain Up level control. ON: The gain up level can be controlled from 0 to 6 dB by using the Manual Gain Control(10). 6: The gain up level control is not available. 10. Manual Gain Control When setting the Switch 6 to the ON position, this control activates. The control range of gain up level is 0 - 6 dB. 11. Pedestal Control The pedestal level can be controlled from 15mV to 80 mV. © © 12. Gamma On/Off Switch ON I 'I IOFF (SW 1) The gamma level of 0.6 or 1.0 can be selected by this switch. ON: 0.6 OFF: 10 13. HD/VD Termination Switch OFF I I I ON (SW 3) Set this switch to the ON position to terminate the HD/VD signals with 75 ohms. 14. HD/VD Output Switch INCO0UT (SW 4) IN: The HD/VD signal can be supplied in this camera. OUT: The HD/VD signal is output from this camera. Note: The equipments connected with this unit should be set to the Hi-Z. PREPARATIONS 1. Power Supply for Camera Prepare a regulated DC power supply which can supply DC 12 V± 10% DC 190 mA or more current and rated CLASS 2. 2. Lenses Be sure to use the optional manual iris lens having the following items. Focus: Adjustable Lens Weight: Less than 300 g (0.66 lbs.) Note: If the lens weight exceed 300 g (0.66 lbs.), the camera and lens should be secured. Mount: C*mount Lens mount should be as shown in the diagram, otherwise the lens will damage the camera. Less than 5/6" (Less than 8 mm) 3. Top and Switch Covers Removal Caution: The following preparation should be made by qualified service personnel or system installers. For selecting Gamma On/Off Switch, HD/VD Termination Selection Switch or HD/VD Output Switch, the top cover of this camera should be removed, And for set...